Help Nokia dbox2 bootloader prob..

[robwillis69]

Hi all i recently crashed my dbox it was going slow,, so i tried to reflash a image back but it couldn't beacuse memory was full... so i then did a flasherase on dbox2 by entering pin 0000 now it boots up saying kien system... So now i have tried flashing now but i get the following error...

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-92.13.1b.07.00.00-06
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root/platform/nokia-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root/platform/mpc8xx-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root/platform/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root.new/platform/nokia-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root.new/platform/mpc8xx-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root.new/platform/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /lost+found/root/platform/nokia-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /lost+found/root/platform/mpc8xx-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /lost+found/root/platform/kernel/os failed
dbox2:root>


I can't seen to fix this it has nothing flash is empty.,,, What canb i do to fix this,, i have trouble reading readme files as everything is in german but i have translated some but nothing about my problem......

[mash4077]

boot net failed

Hi,

check this out:

http://www.dietmar-h.net/flashprob_eng.html

regards
mash

[robwillis69]

Thanks but read all that does not help still the same error...

[robwillis69]

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-92.13.1b.07.00.00-06
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: &_text 0x10000, &_etext 0x26160, &_data 0x26160, &_edata 0x29c50
debug: &_end 0x347dc, &__stack 0x400000
debug: Memory tests (0x400000 -- 0x2000000)
debug: NumberTest: debug: passed
debug: MarchTest: debug: passed
debug: PermTest: debug: passed
dbox2:root> boot net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
boot: elfcopy failed: 16
dbox2:root>

Done what they say on there but i get the elfcopy failed error...

[mash4077]

Hi,

please post the network-log of the bootmanager while flashing (grey box on top of the bootmanager).

regards
mash

[robwillis69]

is this what u mean m8...

***Adapter Desc: VIA Rhine II Fast Ethernet Adapter (Microsoft's Packet Scheduler)
***MAC address: 00:04:61:4C:ED:B1 Local IP: 82.34.9.134 (via Packet-Driver #0)
***BootP server started... Port 67
***TFTP server started... Port 69

[mash4077]

is this what u mean m8...

Yep!

***Adapter Desc: VIA Rhine II Fast Ethernet Adapter (Microsoft's Packet Scheduler)
***MAC address: 00:04:61:4C:ED:B1 Local IP: 82.34.9.134 (via Packet-Driver #0)
***BootP server started... Port 67
***TFTP server started... Port 69

There is no network communication between your PC and your dbox.

Make sure, that your network setup is correct. As far as i can see, you don't set a static ip-address to your pc-networkcard.

regards
mash

[robwillis69]

Arh when my m8 used this prog to flash it orignally he just used a serial lead this is what im doing so i need to connect a cat5 cable to dbox aswell as serial is this correct??

[mash4077]

Yes, flashing without network isn't possible.

regards
mash

[robwillis69]

ok so can u tell me what settings i need to configure my network properties ie 192.168.2.24 is this correct??

[mash4077]

Yes, for example...

If you don't use a hub or switch to connect your dbox to your pc, it is necessary to use a crossover network cable.

Set your network card to the ip-address you mentioned
Set the ip-address of the dbox in the bootmanager for example to 192.168.2.100

make sure that the following has be :

- newest network card driver has been installed
- network card is set to 10MBit/HalfDuplex
- firewall and antivirus software has been switched off or better deleted

regards
mash

[robwillis69]

ok thanks i'll try this and let u know later..

thanks for ur help

regards rob..