Bekomme die Box nicht zum Booten

[Ragnar66]

Huhu

Ich versuche meine Box zu flashen (mit D-Box-Bootmanager)
Aber egal welches Image ich auswähle ich bekomme nur folgende Meldung:
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-95.df.05.08.00.00-f2
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 143000
verify sig: 262
Branching to 0x40000


U-Boot 0.4.0 (TuxBox) JFFS2 only (Aug 15 2003 - 16:44:21)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBox2, Sagem -- Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
LCD: ready
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Scanning JFFS2 FS: ......... .

### FS (jffs2) loading 'var/tuxbox/boot/logo-lcd'
### FS (jffs2) loading 'var/tuxbox/boot/logo-fb'
### FS (jffs2) loading 'var/tuxbox/boot/ppcboot.conf'
### FS (jffs2) loading 'var/tuxbox/boot/u-boot.conf'
### FS (jffs2) loading 'vmlinuz'
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 647997 Bytes = 632.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... Bad Data CRC
=>

Weiter kann ich nix machen

Jemand einen Tip was ich falsch mache?

Gruß Ragnar66

[Unchained]

boot net failed

http://www.dietmar-h.net/flashprob.html#boot_net_failed

[Ragnar66]

Jop - des wars und falsche ppcboot

[Rentakill]

Hi there..

I have just encountered a problem with my Dbox2 when booting.
All was running well untill i shutdown the box via the Menu shutdown option.
Now when i start the Box up , i get the Enigma LCD Display as normal.
Followed by "loading Kernel"
Then " Verifying Checksum"

It is at this stage that the box will just stop.. It will not continue on any furthur..
I have connected to the box using Bootmanager and begin to run the normal proceedure for reflashing an image to the box (Via RS 232).
As the box goes through its normal stage of detecting/Checking and listing the box's status it stops at the following..

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-38.b6.1f.07.00.00-7a
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 200660
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Nov 9 2002 - 01:40:47)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ........ .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: framebuffer on ttyS0
2: framebuffer on fb0
3: framebuffer on null
Select option (1-3), other keys to stop autoboot: 0
..............................................................
Un-Protected 62 sectors
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load compleate: 667093 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 667029 Bytes = 651 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... Bad Data CRC
=> debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-38.b6.1f.07.00.00-7a
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 200660
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Nov 9 2002 - 01:40:47)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ........ .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: framebuffer on ttyS0
2: framebuffer on fb0
3: framebuffer on null
Select option (1-3), other keys to stop autoboot: 0
..............................................................
Un-Protected 62 sectors
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load compleate: 667093 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 667029 Bytes = 651 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... Bad Data CRC

I have been through the forum looking for similar problems and have found others with the same problem, but due to me living in New Zealand and not being able to read German to well, i tend to struggle.

The image i have running on the box has been running for about 2 months without any problems. I havent made any changes previous to the box crashing.
I have the box connected via Ethernet aswell, but allways Use Rs232 for uploading a new image..

Can any one point me in the right direction ???

Thanks

Ren
New Zealand

[mash4077]

boot net failed

Hi,

http://www.dietmar-h.net/flashprob_eng.html

regards
mash4077

[Rentakill]

HI Mash..

Thanks for the reply and URL to an English version of the proceedure.
I have have since tried the proceedure and have had no luck at all.

Is there a way to force Via RS 232 or reset the box totally ?..

Heres my result

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-38.b6.1f.07.00.00-7a
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: &_text 0x10000, &_etext 0x26160, &_data 0x26160, &_edata 0x29c50
debug: &_end 0x347dc, &__stack 0x400000
debug: Memory tests (0x400000 -- 0x2000000)
debug: NumberTest: debug: passed
debug: MarchTest: debug: passed
debug: PermTest: debug: passed
dbox2:root> boot net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
boot: elfcopy failed: 16
dbox2:root>.

I have downloaded and installed that patch as directed for DHCP mediasensing..

Any Ideas ?

Cheers

Ren

[mash4077]

Is there a way to force Via RS 232 or reset the box totally ?..

Flashing is only possible with a well working network.
With a special ppcboot you can try to flash without serial communication, but without network > no chance!

boot: elfcopy failed: 16
dbox2:root>

First of all try to execute "boot net" at this point!

Also make sure that the following is given:

- the newest network card driver are installed
- 10MBit/Halfduplex is fixed
- a crossover cable was used
- firewall and anti virus has been uninstalled
- post your network configuration for further analysis

regards
mash

[Rentakill]

Thanks Mash..


I have entered Boot net Cmd at that point, and still get Boot net Failed.
Elf copy failed 16.

It seems i have a problem with my Network not establishing a connection.
My Network consists of the following..

Realteck RTL8029(AS) 10 Mb Network Card..
Setup half duplex Line transmission
Dbox address 102.168.0.100
I have a Cross over cable connected.. Was working fine 2 days ago.

I notice when running Boot manager i cant have BootP/TFTP Server starten Checked.. If i do, then i get the following :
Error 10049 in Fuction Bind Adress not available

Rs 2323 seems to be the only way i can interogate the box.

[mash4077]

I notice when running Boot manager i cant have BootP/TFTP Server starten Checked.. If i do, then i get the following :
Error 10049 in Fuction Bind Adress not available

Known problem!
Please switch off ICS (Internet Connection Sharing or so...)!

What time is it?

regards
mash

[Rentakill]

Mash.. Your a bloody Legend !!.

Just that.. Disabled ICS , and away she went.
Unreal..

There i was thinking i had almost come to the end of my line.

Now i just have to reload all our local services, and i'm away.
Thanks Heaps.


Talk to you soon

Ren
(New Zealand