Nokia SAT Avia600 2xIntel mit folgendem Problem:
Alle Sender bringen "Kanal zur Zeit nicht verfugbar"
[camd] CA_SEND_MSG: Remote I/O error
[camd] CA_SEND_MSG: Remote I/O error
Frontprozessor gewechselt, SEC, SEC Rams und Tuner bereits sauber ausgelötet-error bleibt. Am SDA/SCL jeweils 5V. Die 14/18 Volt sind nicht da. Alle anderen BetriebsSpannungen sind ok. Fehlen 22KHz am pin 49 des Fronprozessors. Als ich den SEC chip mit Heissluftstation ausgelotet habe und die Box eingesteckt waren 14/18V einmal da, dabei am SDA- 0,5V und SCL-4,9V waren. Beim nächsten Einstecken waren selben Werte wieder da, keine 14/18V und error auf SDA-5v/SCL-5v. Habe Platine mit Fön und Kältespray bearbeitet, hat nichts gebracht. Alle IC,s werden ganz normal warm ( habe gleiche funktionierende box und kann vergleichen).Die Box startet sauber, OSD -in Ordnung.
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: unknown demodulatordebug: BMon V1.2 mID 01
debug: feID 00 gtxID 0b
debug: fpID 5a dsID 01-4f.35.83.07.00.00-11
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 174880
verify sig: 262
Branching to 0x40100
U-Boot 2010.12 (Tuxbox) (04.01.11 20:12:41)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MiB
FLASH: 8 MiB
Using default environment
Scanning JFFS2 FS: ..
.env: found console with value ttyS0
env: found baudrate with value 9600
env: found dbox_duplex with value 0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC
LCD: ready
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 671150 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.11-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 671086 Bytes = 655.4 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.11-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #6 Di 4. Jan 20
:11:58 CET 2011
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600
dbox_duplex=0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:43:fe:3e
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (squashfs+lzma)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.17.3 (2011-01-04 20:12:30 CET)
starting pid 8, tty '': '/etc/init.d/sysinit'
[BOOT] running /etc/init.d/sysinit
Thu Jan 1 01:00:00 UTC 1970
starting pid 22, tty '': '/etc/init.d/rcS'
Please press Enter to activate this console. starting /etc/init.d/S05drivers ...
[BOOT] running /etc/init.d/S05drivers
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Nokia
Model: D-BOX2 (2 flash chips)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.102 2010/05/25 19:58:20 dbt Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 600L found.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
/etc/init.d/S05drivers: line 1: can't create /etc/issue.net: Read-only file syst
em
starting /etc/init.d/S10network ...
starting /etc/init.d/S10rtc ...
starting /etc/init.d/S15syslogd ...
Jan 1 02:00:10 dbox syslog.info syslogd started: BusyBox v1.17.3
starting /etc/init.d/S16lircd ...
starting /etc/init.d/S18rdate ...
starting /etc/init.d/S20inetd ...
starting /etc/init.d/S25cdkVcInfo ...
jtginfo $Id: jtginfo.c,v 2.3 2009/12/20 22:36:51 jtgriker Exp $
starting /etc/init.d/S30autofs ...
[BOOT] Starting the automounter
starting /etc/init.d/S31nfsserver ...
Jan 1 02:00:23 dbox daemon.err automount[169]: failed to load mapInstalling knf
sd (copyright (C) 1996 okir@monad.swb.de).
starting /etc/init.d/S40tuxcald ...
starting /etc/init.d/S40tuxmaild ...
starting /etc/init.d/S99gui ...
$Id: sectionsd.cpp,v 1.319 2010/02/21 10:14:15 rhabarber1848 Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[timerd] woke up from timer? false!
[camd] CA_SEND_MSG: Remote I/O error
[camd] CA_SEND_MSG: Remote I/O error
$Id: zapit.cpp,v 1.453 2010/10/26 20:10:42 dbt Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0 auto_fec 0
[frontend.cpp:CFrontend:63] /dev/dvb/adapter0/frontend0: No such file or directo
ry
/var/tuxbox/config/zapit/services.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[CVideo::setVideoFormat] output format: 4:3(LB)
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[neutrino] SetupFonts filename: /share/fonts/micron.ttf fontname: Micron
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] init menus...
[neutrino] GUI-Personalize instance created...
[neutrino] found esound, adding personalized esound entry to mainmenue
[network config] Instance created
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[drive_setup] Instance created
[neutrino] registering as event client
[scan-setup] received 17 sats
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/l
iblcddisplay.so.0)
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
[sectionsd] getUTC: read: Connection timed out
Kann mir jemand weiterhelfen, wo ich noch suchen soll? Oszilloscope 200Mhz, Schaltplan und Ersatzteile vorhanden.
Vielen Dank und Gruss