Hallo, meine Dbox zeigt seit heute morgen nur noch "Kanal nicht verfügbar", Kanalsuche findet auch nix mehr. Ich habe auch schon ein aktuelles Image geflasht (neuester JtG-Snap mit dem neuen Tunertreiber, Kabeltreiber auf Aus) aber das hat auch nicht gebracht. Ist die Box kaputt ?
Bootlog zeigt folgendes:
5debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID xx-xx.xx.xx.xx.xx.xx-xx
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 162700
verify sig: 262
Branching to 0x40000
U-Boot 1.2.0 (Tuxbox) (May 6 2007 - 21:31:13)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 704134 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 704070 Bytes = 687.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.35-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #1 Sa 28. Jul 17:
27:18 CEST 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30760k available (1200k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:xx:xx:xx:xx:xx
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (SquashFS)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.6.1 (2007-07-05 22:19:02 CEST) multi-call binary
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is on
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
jtginfo $Id: jtginfo.c,v 1.7 2006/08/01 22:04:55 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Thu Jan 1 12:00:00 CET 1970
$Id: sectionsd.cpp,v 1.246 2007/07/18 20:04:25 houdini Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
$Id: zapit.cpp,v 1.402 2007/07/22 14:36:42 dbluelle Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0
avia_gt_core: masking unhandled irq reg 0 bit 7
/tmp/currentservices.xml: No such file or directory
[camd] ca system id: 1722
$Id: controld.cpp,v 1.127 2007/07/01 08:40:13 dbluelle Exp $
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[controld] setting VideoFormat to auto
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
/bin/neutrino: /lib/libpng12.so.0: no version information available (required by
/bin/neutrino)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
[controld] setting VideoFormat to auto
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[controld] setting VideoFormat to auto
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out
Keine Kanalsuche & kein Empfang Dbox2 Kabel 2xI
-
- Beiträge: 1
- Registriert: Freitag 17. August 2007, 03:11
-
- Interessierter
- Beiträge: 39
- Registriert: Freitag 5. Juli 2002, 15:53
Möglicherweise hilft ein anderes Image mit modifizierten Treibern, da UM, früher ISH, im August 2007 etwas geändert haben soll.
Wenn das nichts hilft, dann Folgendes überprüfen.
BFG94 im Tuner oder TS11 (BC369), oder 33 Volt für die Abstimmung der Kapazitätsdioden.
Überstehende Blechlaschen an den Fixierungspunkten mit feiner Zange so drehen, dass der Deckel des Tuners auf der Bestückungsseite abgenommen werden kann.
Spannungen des Tuners messen.
Wenn das nichts hilft, dann Folgendes überprüfen.
BFG94 im Tuner oder TS11 (BC369), oder 33 Volt für die Abstimmung der Kapazitätsdioden.
Überstehende Blechlaschen an den Fixierungspunkten mit feiner Zange so drehen, dass der Deckel des Tuners auf der Bestückungsseite abgenommen werden kann.
Spannungen des Tuners messen.