Danke für die schnelle Antwort!
Habe Kabel durchgeprüft, alle 10 Adern haben Durchgang. Stecker sitzt auch richtig auf dem Modemslot (laut Bild w w w.dboxservice-hallenberg.de/ide/Anleitung/Nokia_20.htm).
Wird was zerschossen wenn der Stecker mal versetzt gesteckt war?
Es ist keine andere Hardware verbaut welche den Interupt hätte dieben können.
Image habe ich nun nochmal neu geflasht, nix eingestellt oder verändert.
IDE-Treiber laden war schon auf on
Da ich zwei IDE-Sets bestellt hatte, habe ich nun die zweite Leiterplatte und das Modemkabel in der gleichen Box verbaut.
In den Logdateien ist jetzt nur einmal die Meldung "hda: lost interrupt "
aber einige Andere mysteriöse Meldungen.
Komme einfach nicht weiter. Kann mir jemand helfen?
Log beim Booten:
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-46.0c.46.07.00.00-48
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
will verify ELF image, start= 0x800000, size= 158020
verify sig: 262
Branching to 0x40000
U-Boot 1.1.4 (Tuxbox) (Aug 7 2006 - 21:15:08)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 679117 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 679053 Bytes = 663.1 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.33.3-dbox2 (vom Jtg-Team) (gcc version 3.4.4) #1 Do Okt 19 10
:49:00 CEST 2006
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30800k available (1152k kernel code, 356k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (
rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1f:65:67
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (SquashFS)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'lti-call
Starting the automounter
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.10 2006/10/04 00:36:41 carjay Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of DBox2 IDE CPLD is at: 0xc38c5000
Probing IDE interface ide0...
hda: TOSHIBA MK4025GAS, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78140160 sectors (40008 MB), CHS=77520/16/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Thu Jan 1 12:00:00 CET 1970
Journalled Block Device driver loaded
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
mount: Mounting /dev/ide/host0/bus0/target0/lun0/part2 on /hdd failed: Invalid a
rgument
/dev/ide/host0/bus0/target0/lun0/disc:
setting standby to 60 (5 minutes)
setting acoustic management to 128
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
HDIO_DRIVE_CMD:ACOUSTIC failed: Input/output error
acoustic = 0 (128=quiet ... 254=fast)
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
jtginfo $Id: jtginfo.c,v 1.7 2006/08/01 22:04:55 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0:0 (VES1893)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
$Id: sectionsd.cpp,v 1.227 2006/06/08 20:19:32 houdini Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
$Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 houdini Exp $
/tmp/currentservices.xml: No such file or directory
[camd] ca system id: 1702
$Id: controld.cpp,v 1.125 2006/09/24 09:17:10 barf Exp $
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[yhtt pd] Webserver nhtt pd/3.0.5 (yhtt pd_core/1.1.1)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[yhtt pd] Webserver starting...
/bin/neutrino: /lib/libpng12.so.0: no version information available (required by
/bin/neutrino)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] initialized everything
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_core: masking unhandled irq reg 0 bit 7
PES, queue 0 normal.
avia_gt_core: masking unhandled irq reg 1 bit 15
TuxTxt service started 68
TuxTxt running thread...(068)
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 16:9)
[sectionsd] getUTC: read: Connection timed out
[timeThread] - 02.07.2007 19:17:09, tim: Mon Jul 2 19:17:09 2007
[sectionsd] readNbytes: received POLLERR
[timeThread] Time set via DVB, going to sleep for 1800 seconds.
[sectionsd] readNbytes: received POLLERR
[sectionsd] readNbytes: received POLLERR
[sectionsd] readNbytes: received POLLERR
Log vom formatieren:
[CPlugins] executing /lib/tuxbox/plugins/hddinit.sh
rm: cannot remove `/var/etc/.ext2': No such file or directory
rm: cannot remove `/var/etc/.ext3': No such file or directory
swapoff: /dev/ide/host0/bus0/target0/lun0/part1: Invalid argument
Checking that no-one is using this disk right now ...
/dev/ide/host0/bus0/target0/lun0: p1 p2
OK
Warning: no primary partition is marked bootable (active)
This does not matter for LILO, but the DOS MBR will not boot this disk.
/dev/ide/host0/bus0/target0/lun0: p1 p2
If you created or changed a DOS partition, /dev/foo7, say, then use dd(1)
to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512 count=1
(See fdisk(8).)
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 16:9)
hda: lost interrupt
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
PCR discontinuity: PCR: 0x069CD984F, OLDPCR: 0x069CCFA30, Diff: 40479
ide0: reset: success
avia_gt_dmx: queue 3 overflow (count: 1)
hda: lost interrupt
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
avia_gt_dmx: queue 3 overflow (count: 2)
ide0: reset: success
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
insmod: A module named xfs already exists
hda: lost interrupt
ide0: unexpected interrupt, status=0x58, count=1
XFS mounting filesystem ide0(3,2)
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: lost interrupt
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
avia_gt_dmx: queue 3 overflow (count: 2)
ide0: reset: success
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
HDIO_DRIVE_CMD:ACOUSTIC failed: Input/output error
