Habe schon alles getestet, Settings neu rein ,Settings gelöscht Suchlauf nichts klappt.Wenn ich die Setings rein spiele kommt kein Bild nach einiger Zeit bunte Mosaike und ruckelnder Ton,aber die Uhrzeit akz etualisiert er richtig und Satfind hat vollen Ausschlag. Spannungen gemessen und Transistoren kontrolliert.
Tuner Spannungen gemessen:
AN :
Pin 1 19,2V
Pin 2 18,8V (warum auch immer???)
Pin 3 12,3V
Pin 7 12V
Pin 8 34V
Pin 9+13 4,8V
Pin 16 3,2V
Alles In Ordnung nur der Pin 2 macht mir Sorgen auch wenn ich umschalte zwischen H/V ändert sich die Spannung am Pin 1 wie es sein sollte.
Habe noch die die Transistoren durchgemessen der LM317T hat 26,9/20,5/19,2
Der TF3 hat alle drei so um die 26V
Der TS11 hat alle so um die 12V
der TF8 beim booten 3V und dann wenn er hochgefahren ist
0,66/0,04/0
der TF6 das ist glaube ich nicht normal hat 0.04/19,3/0
ist dieser Wert 19,3V nicht zu hoch???
was könnte es sein???
Bin für jede Hilfe Dankbar!!!!!
Ach noch was die Schüssel ist I.O. ist ein LNB mit 8 Ausgängen wo mehrere digitale Receiver dran hängen und das Kabel ist auch I.O. meine andere Box läuft hier an dem Anschluss und an einem anderen Anschluss hat die Box daselbe Problem aber vorher ging sie natürlich!!!!
hier der Bootlog Bitte helft mir!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-d6.46.81.07.00.00-12
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/4095/08
WATCHDOG reset enabled
dbo[LCDFONT] FTC_Face_Requester (Fix12/Regular)
hintbox: found string Es wurden keine Kanle gefunden!
hintbox: found string Fhren Sie bitte eine Kanalsuche durch
hintbox: found string (dbox-Taste -> Service)
zapit shot down
/debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-d6.46.81.07.00.00-12
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/4095/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
will verify ELF image, start= 0x800000, size= 156828
verify sig: 263
Branching to 0x40000
U-Boot 1.1.1 (TuxBox) (Oct 30 2004 - 13:18:13)
CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load complete: 613263 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 613199 Bytes = 598.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (vom Jtg-Team) (gcc version 3.3.5) #2 Fri Oct 29 22:
09:59 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=cramfs
Decrementer Frequency = 251625000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30900k available (1040k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:43:f7:43
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x006a0000 : "root (cramfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
route: SIOC[ADD|DEL]RTUsing /lib/modules/2.4.27-dbox2/misc/dvb-core.o
: Network is unreachable
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.94 2004/07/03 01:18:36 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/ves1820.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.oavia_gt_core: masking unhandl
ed irq reg 0 bit 6
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.202 2004/06/24 00:26:58 carjay Exp $
jtginfo $Id: jtginfo.c,v 1.1 2004/05/31 16:00:30 jtgriker Exp $
$Id: sectionsd.cpp,v 1.179 2004/09/10 11:36:00 thegoodguy Exp $
caching 504 hours
events are old 180min after their end time
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
$Id: zapit.cpp,v 1.357 2004/10/27 16:08:42 lucgas Exp $
avia_gt_core: masking unhandled irq reg 0 bit 7
satelliteName = Amos 1 4.0W, satellitePosition = -40
satelliteName = Arabsat 26.0E, satellitePosition = 260
satelliteName = Arabsat 30.5E, satellitePosition = 305
satelliteName = Astra 19.2E, satellitePosition = 192
satelliteName = Astra 1A, Sirius 2/3 5.0E, satellitePosition = 50
satelliteName = Astra 23.5E, satellitePosition = 235
satelliteName = Astra 28.2E, satellitePosition = 282
satelliteName = Eurasia-/Tuerksat 42.0E, satellitePosition = 420
satelliteName = Eutelsat 10.0E, satellitePosition = 100
satelliteName = Eutelsat 13.0E, satellitePosition = 130
satelliteName = Eutelsat 16.0E, satellitePosition = 160
satelliteName = Eutelsat 7.0E, satellitePosition = 70
satelliteName = Eutelsat 8.0W, satellitePosition = -80
satelliteName = HispaSat/PAS 30.0W, satellitePosition = -300
satelliteName = Intelsat 707 1.0W, satellitePosition = -10
satelliteName = Telstar12 15.0W, satellitePosition = -150
satelliteName = Thor 2/3 0.8W, satellitePosition = -8
/var/tuxbox/config/zapit/services.xml: No such file or directory
[camd] ca system id: 1702
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[deutsch.locale] missing entry: movieplayer.pesplayback
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
hintbox: found string Es wurden keine Kanle gefunden!
hintbox: found string Fhren Sie bitte eine Kanalsuche durch
hintbox: found string (dbox-Taste -> Service)
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[neutrino] initialized everything
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
entweder nur Ton oder bildruckeln ohne Ton (Sagem 2xAMD).