wiedereinmal brauche ich Eure Hilfe.
Ich habe heute eine weitere dBox erhalten (SAGEM SAT 1x Intel). Der Debug Mode war kein Problem, auch das Flashen lief gut von der Hand, dann aber die Ernüchertung. Zum einen findet die Box über den Kanalscan nicht einen Sender. Bei einer fertigen Kanalliste kommt immer "Kanal (zu Zeit) nicht verfügbar" - die Zeit ist halt dauernd.
Meine Nokia und meine andere Sagem funktioieren einwandfrei. Daher kann es wohl kein SAT Problem sein.
Wenn ich in den "Satfind" ausführe kommt die Anzeige:
ber: 1656720
snr: 0
sig 32639
zucken bzw. bewegen (die Anzeige wechselt von den Werten her mein ich ;-) )tut sich nichts so wie bei den anderen Boxen.
Was könnte defekt sein?
Bitte helft mir. Falls ich was messen muß bitte genau beschreiben an welchen Punkten.
Danke schon einmal für alle die helfen wollen im Voraus.
Gruß
Neo
Anbei noch das Bootprotokoll:
Code: Alles auswählen
_debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-ea.e2.a5.07.00.00-d0
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 638456 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 638392 Bytes = 623.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:31:1e:b1
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit mode
Intel/Sharp Extended Query Table at 0x0031
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Sagem
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.27-dbox2/avia_av_core: Starting avia_gt_wdt thread.
misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/at76c651.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1993)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Yadi Snapshot vom 26.05.2005 15:51 - Image-Version 2.1.0.3
Networkcfg eth0: 192.168.0.23/255.255.255.0 gw 192.168.0.100
Startmode: Bootmenu - HWS:on
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
Starting pid 95, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.184 2005/05/
02 19:06:35 rasc Exp $
caching 504 hours
events are old 180min after their end time
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for r[camd] ca s
ystem id: 1702
eading.
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
[timeThread] time(): 05.06.2005 15:14:08, tim: Sun Jun 5 15:14:08 2005
[timeThread] time(): 05.06.2005 15:14:09, tim: Sun Jun 5 15:14:09 2005
[getservices] dup transponder id 12C onid 1
[getservices] dup transponder id 12C onid 1
[getservices] dup transponder id 1 onid 13E
[getservices] dup transponder id 1CE8 onid 38
[getservices] dup transponder id 1 onid 1
[getservices] dup transponder id 1E14 onid 13E
[getservices] dup transponder id 65 onid 13E
[getservices] dup transponder id 21FC onid 13E
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[getservices] dup transponder id C9 onid 6
[camd] no card is in slot #2
[camd] no card is in slot #1
[getservices] dup transponder id 3138 onid B0
[getservices] dup transponder id 319C onid 13E
[getservices] dup transponder id 3CF0 onid 13E
[getservices] dup transponder id 5 onid 85
/var/tuxbox/config/zapit/antiservices.xml: No such file or directory
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 457 onid 1
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
/dev/input/event1: No such file or directory
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] menue setup
[basicsocket] send_data: Resource temporarily unavailable
loading locales: scandir: No such file or directory
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] received 17 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] initialized everything
zap failed!
zap failed!
