ich kann euch versichern das ich keine 100mbit karte hab und mit sicherheit kein 1:1 patchkabel
.aber an dieser box verzweifel ich noch, ich vermute das die netzwerkkarte nen knaller weg hat.
ich bekomme weder nen ping noch zeigt der bootmanager was brauchbares an.
falls die eth defekt ist, kann man die tauschen? bzw den chip erneuern, past der chip von ner philips box???
achso ist ne SAGEM mit 1xIntel und BMON 1.2
thx und cu purple
-----------------------------------------------------------------------------
1.Versuch
Nur Box einschalten:
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID xxxxxxxxxxxxxx
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
--------------------------------------------------------------------------------
2.Versuch
Box über ppcboot booten, image in 13.img umbenannt:
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID xxxxxxxxxxxxxxxxxxx
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
---------------------------------------------------------------------------------
3.Versuch
Box einschalten und auf-taste gedrückt halten:
:debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID xxxxxxxxxxxxxxxxx
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: &_text 0x10000, &_etext 0x26ec0, &_data 0x26ec0, &_edata 0x2a9bc
debug: &_end 0x35944, &__stack 0x400000
debug: Memory tests (0x400000 -- 0x2000000)
debug: NumberTest: debug: passed
debug: MarchTest: debug: passed
debug: PermTest: debug: passed
dbox2:root>
---------------------------------------------------------------------------------
4.Versuch
Box einschalten und auf-taste gedrückt halten, box mit boot flash starten:
:debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID xxxxxxxxxxxxxxxxx
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: &_text 0x10000, &_etext 0x26ec0, &_data 0x26ec0, &_edata 0x2a9bc
debug: &_end 0x35944, &__stack 0x400000
debug: Memory tests (0x400000 -- 0x2000000)
debug: NumberTest: debug: passed
debug: MarchTest: debug: passed
debug: PermTest: debug: passed
dbox2:root> boot flash
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 143000
verify sig: 262
Branching to 0x40000
U-Boot 0.4.0 (TuxBox) JFFS2 only (Aug 15 2003 - 16:44:21)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBox2, Sagem -- Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
LCD: ready
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Scanning JFFS2 FS: .....
.### FS (jffs2) loading 'var/tuxbox/boot/logo-lcd'
### FS (jffs2) loading 'var/tuxbox/boot/logo-fb'
### FS (jffs2) loading 'var/tuxbox/boot/ppcboot.conf'
### FS (jffs2) loading 'var/tuxbox/boot/u-boot.conf'
### FS (jffs2) loading 'vmlinuz'
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 648783 Bytes = 633.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.22-dbox2 (root@zor-pc) (gcc version 3.2.3) #1 Sun Sep 28 19:26
:31 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rw console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30800k available (1100k kernel code, 408k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, xxxxxxxxxxxx
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit mode
Intel/Sharp Extended Query Table at 0x0031
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00800000 : "root (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cramfs: wrong magic
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x007600b8: 0x0010 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x007600d8: 0x0010 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x007600ec: 0x1000 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x007600f4: 0x0100 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00760100: 0x0040 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00760108: 0x0050 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00760110: 0x0040 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00760114: 0x0010 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00760120: 0x0010 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00760134: 0x0010 in
stead
Further such events for this erase block will not be printed
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 12, console /dev/co/bin/sh: run-parts: not foundti-c
/bin/sh: run-parts: not found
SR.4 or SR.5 bits set in buffer write (status a8). Clearing.
Newly-erased block contained word 0x0 at offset 0x00760000
Detected STB:
Vendor: Sagem
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter PowerPC 8xx I2C adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
event: $Id: event.c,v 1.11 2003/09/08 22:38:56 obi Exp $
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [PowerPC
8xx I2C adapter](pos. 0).
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 2).
$Id: cam.c,v 1.24 2003/09/08 23:16:17 obi Exp $
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [PowerPC 8xx I2C adapter](p
os. 3).
CAM: attached to adapter PowerPC 8xx I2C adapter
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_av: $Id: avia_av_core.c,v 1.75 2003/09/12 04:46:54 obi Exp $
avia_av_event: $Id: avia_av_event.c,v 1.10 2003/07/24 01:59:21 homar Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.10 2003/07/24 01:59:21 homar Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.41 2003/09/12 04:41:15 obi Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.20 2003/08/01 17:31:22 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.18 2003/08/01 17:31:21 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.187 2003/09/12 02:46:30 obi Exp $
avia_gt_dmx: loaded ucode v0014
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.36 2003/09/23 21:48:34 zwen Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.27 2003/09/12 04:41:16 obi Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.31 2003/09/19 15:58:55 alexw Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.39 2003/08/01 17:31:22 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.50 2003/09/13 02:45:12 obi Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.13 2003/08/01 17:31:22 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.29 2003/09/12 04:41:16 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.22 2003/08/01 17:31:22 obi Exp $
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.11 2003/08/01 17:31:22 obi Exp $
Warning: /lib/modules/2.4.22-dbox2/misc/avia_gt_proc.o symbol for parameter degu
g not found
avia_gt_proc: Using config file '/var/tuxbox/config/avia.conf'.
avia_gt_proc: $Id: avia_gt_proc.c,v 0.92d 2003/06/18 19:00:00 bofh Exp $
avia_gt_proc: found - AVIA eNX
Module avia_gt_proc loaded, with warnings
$Id: avia_napi.c,v 1.16 2003/07/24 01:59:22 homar Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
DVB: registering frontend 0:0 (Atmel AT76C651A with DAT7021)...
VES1x93 not found (identity 00)
i2c-core.o: client [dvb] registered to adapter [PowerPC 8xx I2C adapter](pos. 4)
.
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.7 2003/09/11 23:22:47 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.25 2003/09/12 03:01:51 obi Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.187 2003/09/11 23:22:48 obi Exp $
avia_gt_napi: hw section filtering enabled.
Starting pid 72, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.167 2003/06/
18 12:19:23 alexw Exp $
caching 504 hours
events are old 60min after their end time
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.331 2003/09/28 12:40:13 alexw Exp $
[mgcam] using mgcam_porter
$Id: controld.cpp,v 1.108 2003/08/26 20:13:55 zwen Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[controld] Unknown aspectRatio: 0[controld] setting VideoFormat to auto
[nhttpd] Neutrino HTTP-Server starting..
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[camd] no card is in slot #2
[camd] a card is in slot #1
Mount(1) 192.168.111.21:mp3 -> /mnt/mp3
mount: Mounting //192.168.111.21/mp3 on /mnt/mp3 failed: No such file or directo
ry
[neutrino]: NFS mount error: "mount -t cifs //192.168.111.21/mp3 /mnt/mp3 -o use
rname=DBOX2,password=DBOX2,unc=//192.168.111.21/mp3,ro,soft,udp,nolock,rsize=819
2,wsize=8192"
Mount(1) 192.168.111.21:filme -> /mnt/filme
mount: Mounting //192.168.111.21/filme on /mnt/filme failed: No such file or dir
ectory
[neutrino]: NFS mount error: "mount -t cifs //192.168.111.21/filme /mnt/filme -o
username=DBOX2,password=DBOX2,unc=//192.168.111.21/filme,ro,soft,udp,nolock,rsi
ze=8192,wsize=8192"
Mount(1) 192.168.111.21:bilder -> /mnt/bilder
mount: Mounting //192.168.111.21/bilder on /mnt/bilder failed: No such file or d
irectory
[neutrino]: NFS mount error: "mount -t cifs //192.168.111.21/bilder /mnt/bilder
-o username=DBOX2,password=DBOX2,unc=//192.168.111.21/bilder,ro,soft,udp,nolock,
rsize=8192,wsize=8192"
[neutrino] vcrControl Instance created
CVCRControl registered new serverdevice: ngrab
[neutrino] menue setup
loading locales: scandir: No such file or directory
[controld] setting VideoFormat to auto
video notify: videomenu.videoformat
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out
