Ich bitte um Hilfe bei meinem Problem.
Nokia Sat (Avia600)
IDE Interface
Schaltregler 27 V, 3V > 5 V
2,5" HD
Ich habe heute das IDE-Interface und diesen internen Schaltregler mit den Eingangsseitig 3 Anschlußkabeln eingebaut. Beim Einstecken der DBOX blieb die LED dunkel. Ich habe dann den Netzstecker sofort gezogen. Mit einer Lupe habe ich einen Kurzschluss auf dem Schaltregler zwischen 3V und 27 V festgestellt. Somit hat der 3 V Teil der Box kurzzeitig 24 V erhalten (
Folgendes tritt jetzt (bei abgezogenen Schaltregler) auf:
Die Box fährt hoch und macht nach ca. 30 sec einen Reset.
Ich habe sie dann neu geflasht. Solange ich per FTP keine Ucodes einspiele stürzt sie nicht ab. Wenn ich die UCodes einspiele und neu starte kommt immer wieder ein Reset nach ca 30 Sec oder die Box bleibt einfach beim Booten stehen.
--------------------------------cut
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
--------------------------------cut
Bei der Zeile im Log bleibt die Box stehen.
Ich möchte hier nicht einfach lange Logfiles posten aber wenn mir jemand helfen kann geht das natürlich detaillierter. Es sieht für mich so aus wenn der Avia angesprochen wird geht nichts mehr.
Wer kann so einen Fehler reparieren ?
Gruß,
Thomas
Nokia b. Einbau des Schaltreglers für 2,5"HD zerstört
-
- Neugieriger
- Beiträge: 12
- Registriert: Sonntag 13. Mai 2007, 19:35
Nokia b. Einbau des Schaltreglers für 2,5"HD zerstört
Zuletzt geändert von Radio Nordsee am Sonntag 3. Juni 2007, 02:43, insgesamt 1-mal geändert.
-
- Image-Team
- Beiträge: 1015
- Registriert: Freitag 7. Februar 2003, 18:37
-
- Neugieriger
- Beiträge: 12
- Registriert: Sonntag 13. Mai 2007, 19:35
So was blödes:
Zur Schutz vor Spammern musst Du mindestens 10 Beitraege geschrieben und laenger als 7 Tage im Forum registriert sein, bevor Du einen U R L (Link) posten kannst. Bitte habe Verstaendnis fuer diese Massnahme.
Danke!
Ich habe fast 30 Minuten die Log es zusammen gestellt und jetzt kann ich die nicht posten. Ein Link ist da gar nicht drin.
Gruß,
Thomas
Zur Schutz vor Spammern musst Du mindestens 10 Beitraege geschrieben und laenger als 7 Tage im Forum registriert sein, bevor Du einen U R L (Link) posten kannst. Bitte habe Verstaendnis fuer diese Massnahme.
Danke!
Ich habe fast 30 Minuten die Log es zusammen gestellt und jetzt kann ich die nicht posten. Ein Link ist da gar nicht drin.
Gruß,
Thomas
-
- Neugieriger
- Beiträge: 12
- Registriert: Sonntag 13. Mai 2007, 19:35
Geht doch . Here you are.
Das 1. Log wenn die UCodes eingespielt worden sind:
----------------------------cut---
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-09.bd.3c.07.00.00-28
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 638456 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 638392 Bytes = 623.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
---------------------------------------------------cut---
ab hier steht die Box und macht nicht weiter.
Jetzt flasche ich nochmal ein Image:
----------------------------------------------------cut---
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-09.bd.3c.07.00.00-28
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 638456 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 638392 Bytes = 623.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia60
0.ux'.
avia_av: microcode not found, setting up dummy
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vFFFF
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/ves1820.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
avia_gt_napi: forcing spts mode.
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
Yadi Snapshot vom 26.05.2005 15:51 - Image-Version 2.1.0.3
Networkcfg eth0: 0.0.0.0/0.0.0.0 gw 0.0.0.0
Startmode: Bootmenu - HWS:on
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
$Id: lcdip.cpp,v 1.5 2005/04/11 22:17:30 mogway Exp $
Starting pid 96, console /dev/console: '/etc/init.d/start'
Starting pid 97, console /dev/console: '/bin/sh'
BusyBox v1.00 (2005.05.26-14:39+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/ #
/ # $Id: sectionsd.cpp,v 1.184 2005/05/02 19:06:35 rasc Exp $
caching 504 hours
events are old 180min after their end time
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] CA_SEND_MSG: No such device
[camd] CA_SEND_MSG: No such device
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
avia_av: new_audio_config timeout
[ConfigFile] Unable to open file /var/tuxbox/config/nhttpd.conf for reading.
avia_av: new_audio_config timeout
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[ConfigFile] Unable to open file /var/tuxbox/config/neutrino.conf for reading.
[ConfigFile] Unable to open file /var/tuxbox/config/scan.conf for reading.
[neutrino] Loading of scan settings failed. Using defaults.
cannot read locale: No such file or directory
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[neutrino] initialized everything
[sectionsd] getUTC: read: Connection timed out
---------------------------------------------------------cut
jetzt gehe ich mit ftp auf die Box und fülle den Ordner "ucodes"
jetzt reset und noch ein Log:
----------------------------------------------------------cut
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
jffs2_get_inode_nodes(): CRC failed on node at 0x00046724: Read 0xffffffff, calc
ulated 0x3930d31f
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 32007 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a7ff)
insmod: init_module: avia_av: Input/output error
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_av_set_stc
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
Using /lib/modules/2.4.27-dbox2/misc/ves1820.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_dmx_tap
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
insmod: unresolved symbol avia_gt_napi_dvr_send
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_gt_set_playback_mode
insmod: unresolved symbol avia_gt_get_playback_mode
insmod: unresolved symbol avia_av_is500
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_av_new_audio_config
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Yadi Snapshot vom 26.05.2005 15:51 - Image-Version 2.1.0.3
Networkcfg eth0: 192.168.178.122
192.168.178.1/255.255.255.0 gw 192.168.178.
Startmode: Bootmenu - HWS:on
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
Starting pid 93, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.184 2005/05/
02 19:06:35 rasc Exp $
caching 504 hours
events are old 180min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] /dev/dvb/adapter0/demux0: No such file or directory
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
/var/tuxbox/config/zapit/services.xml: No such file or directory
[sectionsd] open dmx: No such file or directory
[audio.cpp:CAudio:34] /dev/dvb/adapter0/audio0: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[aviaext.cpp:CAViAext:37] /dev/dbox/aviaEXT: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[sectionsd] getUTC: open: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld] /dev/dvb/adapter0/video0: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[neutrino] frameBuffer Instance created
[sectionsd] getUTC: open: No such file or directory
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
FBIOGET_FSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[sectionsd] open dmx: No such file or directory
zapit shot down
Waiting for controld (max. 9 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 8 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 7 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 6 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Starting pid 181, console /dev/console: '/bin/switch'
CXA2092 found
The system is going down NOW !![nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
----------------------------------------------------cut
jetzt noch einmal einen Reset und ein noch ein Log:
-----------------------------------------------------cut
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 638392 Bytes = 623.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 32007 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a7ff)
insmod: init_module: avia_av: Input/output error
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_av_set_stc
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
Using /lib/modules/2.4.27-dbox2/misc/ves1820.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_dmx_tap
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
insmod: unresolved symbol avia_gt_napi_dvr_send
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_gt_set_playback_mode
insmod: unresolved symbol avia_gt_get_playback_mode
insmod: unresolved symbol avia_av_is500
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_av_new_audio_config
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Yadi Snapshot vom 26.05.2005 15:51 - Image-Version 2.1.0.3
Networkcfg eth0: 192.168.178.122
192.168.178.1/255.255.255.0 gw 192.168.178.
Startmode: Bootmenu - HWS:on
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
Starting pid 93, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.184 2005/05/
02 19:06:35 rasc Exp $
caching 504 hours
events are old 180min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] /dev/dvb/adapter0/demux0: No such file or directory
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
/var/tuxbox/config/zapit/services.xml: No such file or directory
[audio.cpp:CAudio:34] /dev/dvb/adapter0/audio0: No such file or directory
[sectionsd] open dmx: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[aviaext.cpp:CAViAext:37] /dev/dbox/aviaEXT: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[sectionsd] getUTC: open: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld] /dev/dvb/adapter0/video0: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[sectionsd] getUTC: open: No such file or directory
FBIOGET_FSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[sectionsd] open dmx: No such file or directory
zapit shot down
Waiting for controld (max. 9 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 8 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 7 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 6 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Starting pid 181, console /dev/console: '/bin/switch'
CXA2092 found
The system is going down NOW !![nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
---------------------------------------------------------------cut
Ich hoffe dass das jetzt nicht zu unübersichtlich war.
Vielen Dank für es lesen.
Gruß,
Thomas
Das 1. Log wenn die UCodes eingespielt worden sind:
----------------------------cut---
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-09.bd.3c.07.00.00-28
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 638456 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 638392 Bytes = 623.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
---------------------------------------------------cut---
ab hier steht die Box und macht nicht weiter.
Jetzt flasche ich nochmal ein Image:
----------------------------------------------------cut---
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-09.bd.3c.07.00.00-28
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 638456 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 638392 Bytes = 623.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia60
0.ux'.
avia_av: microcode not found, setting up dummy
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vFFFF
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/ves1820.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
avia_gt_napi: forcing spts mode.
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
Yadi Snapshot vom 26.05.2005 15:51 - Image-Version 2.1.0.3
Networkcfg eth0: 0.0.0.0/0.0.0.0 gw 0.0.0.0
Startmode: Bootmenu - HWS:on
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
$Id: lcdip.cpp,v 1.5 2005/04/11 22:17:30 mogway Exp $
Starting pid 96, console /dev/console: '/etc/init.d/start'
Starting pid 97, console /dev/console: '/bin/sh'
BusyBox v1.00 (2005.05.26-14:39+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/ #
/ # $Id: sectionsd.cpp,v 1.184 2005/05/02 19:06:35 rasc Exp $
caching 504 hours
events are old 180min after their end time
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] CA_SEND_MSG: No such device
[camd] CA_SEND_MSG: No such device
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
avia_av: new_audio_config timeout
[ConfigFile] Unable to open file /var/tuxbox/config/nhttpd.conf for reading.
avia_av: new_audio_config timeout
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[ConfigFile] Unable to open file /var/tuxbox/config/neutrino.conf for reading.
[ConfigFile] Unable to open file /var/tuxbox/config/scan.conf for reading.
[neutrino] Loading of scan settings failed. Using defaults.
cannot read locale: No such file or directory
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[neutrino] initialized everything
[sectionsd] getUTC: read: Connection timed out
---------------------------------------------------------cut
jetzt gehe ich mit ftp auf die Box und fülle den Ordner "ucodes"
jetzt reset und noch ein Log:
----------------------------------------------------------cut
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
jffs2_get_inode_nodes(): CRC failed on node at 0x00046724: Read 0xffffffff, calc
ulated 0x3930d31f
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 32007 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a7ff)
insmod: init_module: avia_av: Input/output error
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_av_set_stc
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
Using /lib/modules/2.4.27-dbox2/misc/ves1820.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_dmx_tap
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
insmod: unresolved symbol avia_gt_napi_dvr_send
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_gt_set_playback_mode
insmod: unresolved symbol avia_gt_get_playback_mode
insmod: unresolved symbol avia_av_is500
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_av_new_audio_config
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Yadi Snapshot vom 26.05.2005 15:51 - Image-Version 2.1.0.3
Networkcfg eth0: 192.168.178.122
192.168.178.1/255.255.255.0 gw 192.168.178.
Startmode: Bootmenu - HWS:on
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
Starting pid 93, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.184 2005/05/
02 19:06:35 rasc Exp $
caching 504 hours
events are old 180min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] /dev/dvb/adapter0/demux0: No such file or directory
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
/var/tuxbox/config/zapit/services.xml: No such file or directory
[sectionsd] open dmx: No such file or directory
[audio.cpp:CAudio:34] /dev/dvb/adapter0/audio0: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[aviaext.cpp:CAViAext:37] /dev/dbox/aviaEXT: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[sectionsd] getUTC: open: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld] /dev/dvb/adapter0/video0: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[neutrino] frameBuffer Instance created
[sectionsd] getUTC: open: No such file or directory
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
FBIOGET_FSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[sectionsd] open dmx: No such file or directory
zapit shot down
Waiting for controld (max. 9 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 8 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 7 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 6 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Starting pid 181, console /dev/console: '/bin/switch'
CXA2092 found
The system is going down NOW !![nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
----------------------------------------------------cut
jetzt noch einmal einen Reset und ein noch ein Log:
-----------------------------------------------------cut
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 638392 Bytes = 623.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Do Mai 26
17:25:49 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30880k available (1088k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:f7:47
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 32007 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a7ff)
insmod: init_module: avia_av: Input/output error
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_av_set_stc
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
Using /lib/modules/2.4.27-dbox2/misc/ves1820.o
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_dmx_tap
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
insmod: unresolved symbol avia_gt_napi_dvr_send
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_gt_set_playback_mode
insmod: unresolved symbol avia_gt_get_playback_mode
insmod: unresolved symbol avia_av_is500
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_av_new_audio_config
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Yadi Snapshot vom 26.05.2005 15:51 - Image-Version 2.1.0.3
Networkcfg eth0: 192.168.178.122
192.168.178.1/255.255.255.0 gw 192.168.178.
Startmode: Bootmenu - HWS:on
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
Starting pid 93, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.184 2005/05/
02 19:06:35 rasc Exp $
caching 504 hours
events are old 180min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] /dev/dvb/adapter0/demux0: No such file or directory
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
/var/tuxbox/config/zapit/services.xml: No such file or directory
[audio.cpp:CAudio:34] /dev/dvb/adapter0/audio0: No such file or directory
[sectionsd] open dmx: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[aviaext.cpp:CAViAext:37] /dev/dbox/aviaEXT: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[sectionsd] getUTC: open: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld] /dev/dvb/adapter0/video0: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[sectionsd] getUTC: open: No such file or directory
FBIOGET_FSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[sectionsd] open dmx: No such file or directory
zapit shot down
Waiting for controld (max. 9 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 8 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 7 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 6 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Starting pid 181, console /dev/console: '/bin/switch'
CXA2092 found
The system is going down NOW !![nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
---------------------------------------------------------------cut
Ich hoffe dass das jetzt nicht zu unübersichtlich war.
Vielen Dank für es lesen.
Gruß,
Thomas
-
- Tuxboxer
- Beiträge: 6119
- Registriert: Mittwoch 3. April 2002, 00:32
-
- Neugieriger
- Beiträge: 12
- Registriert: Sonntag 13. Mai 2007, 19:35
Die maßgeblichen Zeilen aus dem Log sind vermutlich diese:
----------------
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 32007 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a7ff)
insmod: init_module: avia_av: Input/output error
----------------
Ist hier zu erkennen welcher Chip defekt ist ?
Gruß,
Thomas
----------------
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 32007 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a7ff)
insmod: init_module: avia_av: Input/output error
----------------
Ist hier zu erkennen welcher Chip defekt ist ?
Gruß,
Thomas
-
- Neugieriger
- Beiträge: 12
- Registriert: Sonntag 13. Mai 2007, 19:35
Danke für den Hinweis. Mein letzter Post hat sich wohl gerade mit Deiner Antwort überschnitten.SoLaLa hat geschrieben:hmmm, alles zusammen betrachtet würd ich auf den Avia600, aber eher noch auf dessen Ram tippen.
Dabei hast Du noch Glück gehabt. Wenn die 27V wirklich auf der 3V Schiene landen, dann geht da meist mehr kaputt
Ich habe den Netzstecker auch sofort wieder gezogen. Trotzdem ist das alles sehr dumm gelaufen. Habe hier das IDE Interface und den jetzt - nachdem ich mit einem Messer den Faden Lötzinn zwischen den Pins entfernt habe - funktionierenden Schaltregler und eine neue 2,5" HD mit einer vorher einwandfrei funktionierenden Nokia herumstehen.
Zuletzt geändert von Radio Nordsee am Sonntag 3. Juni 2007, 11:19, insgesamt 2-mal geändert.
-
- Tuxboxer
- Beiträge: 6119
- Registriert: Mittwoch 3. April 2002, 00:32