hallo leute,
erstmal ein erfolgreiches und gesundes neues jahr!
habe vor kurzem meine dbox2 nokia auf linux (neutrino) umgebaut, seitdem findet die box keine sender mehr, obwohl sie vorher bei original betaresearch noch 100% funktionierte, kann es sein das durch den umbau irgend etwas zerschossen wurde?
habe mich dei dbox2hardware.de etwas schlau gemacht und den tuner und motherboard bei den angegebenen lötpunkten durch gemessen, alle spannungen sind vorhanden!
dann steht weiter unten in der beschreibung:
Sollten alle Spannungen vorhanden sein und trotzdem geht nichts, dann ist es immer noch möglich das die Box dir mitteilt “Kanal zur Zeit nicht verfügbar†oder UD4 bei der Betanova. Dann kann der Tuner zwar einwandfrei arbeiten aber da der Stream vor dem Durchschreiten des GTX/ENX und des Avias noch zuvor durch das SoftCam muß, kann diese Fehlermeldung auch hier ihre Ursache haben.
was bedeutet das , muß ich die box wirklich zur reparatur weggeben, oder kann man sie doch noch irgendwie selber retten?
box funktioniert soweit einwandfrei, alle menüs sind da, nur wenn ich die bouget.xml oder die service.xml einspiele kommt "kanal zur zeit nicht verfügbar", wenn ich dann eine kanalsuche mache, findet sie keine transponder und keine kanäle
vielleicht weiß jemand einen rat und kann mir helfen, wo das problem liegt, ohne das ich sie wegschicken muß
danke
krusius
Brauche Hilfe, DBox2 Nokia Sat findet keine Sender mehr
-
krusius
- Neugieriger
- Beiträge: 7
- Registriert: Sonntag 1. Januar 2006, 14:30
-
mash4077
- Tuxboxer
- Beiträge: 4654
- Registriert: Samstag 27. April 2002, 13:19
-
krusius
- Neugieriger
- Beiträge: 7
- Registriert: Sonntag 1. Januar 2006, 14:30
-
mash4077
- Tuxboxer
- Beiträge: 4654
- Registriert: Samstag 27. April 2002, 13:19
-
krusius
- Neugieriger
- Beiträge: 7
- Registriert: Sonntag 1. Januar 2006, 14:30
-
mash4077
- Tuxboxer
- Beiträge: 4654
- Registriert: Samstag 27. April 2002, 13:19
-
krusius
- Neugieriger
- Beiträge: 7
- Registriert: Sonntag 1. Januar 2006, 14:30
danke für den tip, hier ist die bootlog:
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-ef.50.04.07.00.00-d1
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
will verify ELF image, start= 0x800000, size= 153668
verify sig: 262
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (Nov 12 2005 - 14:23:49)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ..
.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 660958 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 660894 Bytes = 645.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.31-dbox2 (elvis@linux) (gcc version 3.4.4) #241 Di Dez 13 18:4
2:12 CET 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30844k available (1120k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:15:68:da
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00540000 : "root (squashfs)"
0x00540000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.31-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.31-dbox2/misc/multicam.o
DBox2 Multicam Driver v1.01 skars & doz21
Using /lib/modules/2.4.31-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.31-dbox2/misc/avs.o
Using /lib/modules/2.4.31-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.31-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.31-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.31-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.31-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.31-dbox2/misc/avia_av.o
route: SIOC[ADD|DEL]RT: Network is unreachable
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v001A
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.31-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/ves1820.o
Using /lib/modules/2.4.31-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.31-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.31-dbox2/misc/aviaEXT.o
Starting pid 82, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.195 2005/11/07 16:33:34 metallica Exp $
caching 504 hours
events are old 180min after their end time
logcsd Version 1.32 started
Gbox wird nicht gestartet
/var/plugins/start_camd: 14: /var/emu/camd3: Permission denied
EvoCamd wird nicht gestartet
NewCamd wird nicht gestartet
Camd2 wird nicht gestartet
Scam wird nicht gestartet
MGCamd wird nicht gestartet
$Id: zapit.cpp,v 1.374 2005/09/26 21:59:54 Kroki & Worschter Exp $
[zapit] MAX_SOCKETS=10
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[neutrino] enable flash
[neutrino] Software update enabled
[basicsocket] send_data: Resource temporarily unavailable
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...[basicsocket] send_data: Resourc
e temporarily unavailable
OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-ef.50.04.07.00.00-d1
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
will verify ELF image, start= 0x800000, size= 153668
verify sig: 262
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (Nov 12 2005 - 14:23:49)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ..
.FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 660958 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 660894 Bytes = 645.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.31-dbox2 (elvis@linux) (gcc version 3.4.4) #241 Di Dez 13 18:4
2:12 CET 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30844k available (1120k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:15:68:da
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00540000 : "root (squashfs)"
0x00540000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.31-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.31-dbox2/misc/multicam.o
DBox2 Multicam Driver v1.01 skars & doz21
Using /lib/modules/2.4.31-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.31-dbox2/misc/avs.o
Using /lib/modules/2.4.31-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.31-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.31-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.31-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.31-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.31-dbox2/misc/avia_av.o
route: SIOC[ADD|DEL]RT: Network is unreachable
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v001A
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.31-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/ves1820.o
Using /lib/modules/2.4.31-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.31-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.31-dbox2/misc/aviaEXT.o
Starting pid 82, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.195 2005/11/07 16:33:34 metallica Exp $
caching 504 hours
events are old 180min after their end time
logcsd Version 1.32 started
Gbox wird nicht gestartet
/var/plugins/start_camd: 14: /var/emu/camd3: Permission denied
EvoCamd wird nicht gestartet
NewCamd wird nicht gestartet
Camd2 wird nicht gestartet
Scam wird nicht gestartet
MGCamd wird nicht gestartet
$Id: zapit.cpp,v 1.374 2005/09/26 21:59:54 Kroki & Worschter Exp $
[zapit] MAX_SOCKETS=10
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[neutrino] enable flash
[neutrino] Software update enabled
[basicsocket] send_data: Resource temporarily unavailable
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...[basicsocket] send_data: Resourc
e temporarily unavailable
OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out
-
mash4077
- Tuxboxer
- Beiträge: 4654
- Registriert: Samstag 27. April 2002, 13:19
Sowas wird hier nicht unterstützt. Mach dir ein ordentliches Image drauf, dann sehen wir weiter.krusius hat geschrieben:Using /lib/modules/2.4.31-dbox2/misc/multicam.o
DBox2 Multicam Driver v1.01 skars & doz21
logcsd Version 1.32 started
Gbox wird nicht gestartet
/var/plugins/start_camd: 14: /var/emu/schwarzglotz: Permission denied
EvoCamd wird nicht gestartet
NewCamd wird nicht gestartet
Camd2 wird nicht gestartet
Scam wird nicht gestartet
MGCamd wird nicht gestartet
$Id: zapit.cpp,v 1.374 2005/09/26 21:59:54 Kroki & Worschter Exp $
[zapit] MAX_SOCKETS=10
Gruß
mash
-
krusius
- Neugieriger
- Beiträge: 7
- Registriert: Sonntag 1. Januar 2006, 14:30
entschuldigung, hoffe daß das ein ordentliches image ist und du kannst mir weiterhelfen?
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-ef.50.04.07.00.00-d1
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Aug 5 2002 - 09:06:03)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ..
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 640967 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 640903 Bytes = 625 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.21-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Jul 6 12:22:55 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30804k available (1128k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:15:68:da
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'Using /lib/modules/2.4.2
1-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.21-dbox2/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.21-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.21-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.21-dbox2/misc/saa7126.o
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [](pos. 1).
Using /lib/modules/2.4.21-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.21-dbox2/misc/dvb_demux.o
Using /lib/modules/2.4.21-dbox2/misc/dvbdev.o
Using /lib/modules/2.4.21-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
Using /lib/modules/2.4.21-dbox2/misc/avia.o
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
Using /lib/modules/2.4.21-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.21-dbox2/misc/dmxdev.o
Using /lib/modules/2.4.21-dbox2/misc/dvb_frontend.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.21-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.23.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.8.4.2 2003/07/22 08:01:56 alexw Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.139.2.1.2.5 2003/06/04 11:04:45 alexw Exp $
avia_gt_dmx: No firmware found at /var/tuxbox/ucodes/ucode.bin, using compiled-i
n version.
avia_gt_dmx: Successfully loaded ucode V0.14
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.25.4.4 2003/07/22 08:01:56 alexw Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.19.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.21-dbox2/misc/dvb.o
dvb.c: init_dvb
Init VES1893
Using /lib/modules/2.4.21-dbox2/misc/ves1893.o
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
VES1893: attaching VES1893 at 0x10 to adapter
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.141.2.1.2.1 2003/02/18 14:32:46 alexw Exp
$
avia_gt_napi: hardware section filtering enabled.
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.17.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.38.4.6 2003/07/22 08:01:56 alexw Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.12.4.1 2003/02/18 14:32:46 alexw Exp $
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.4 2002/08/22 13:39:33 Jolt Exp $
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.4 2003/07/22 08:33:41 alexW Exp $
$Id: sectionsd.cpp,v 1.167 2003/06/18 12:19:23 alexw Exp $
caching 504 hours
events are old 60min after their end time
$Id: zapit.cpp,v 1.290.2.50 2003/06/13 10:53:15 digi_casi Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
$Id: controld.cpp,v 1.107 2003/06/26 05:08:58 alexw Exp $
[controld] Boxtype detected: (1)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.477 2003/07/16 08:58:13 thegoodguy E
xp $
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[sectionsd] getUTC: read: Connection timed out
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-ef.50.04.07.00.00-d1
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Aug 5 2002 - 09:06:03)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 640967 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 640903 Bytes = 625 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.21-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Jul 6 12:22:55 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30804k available (1128k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:15:68:da
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'Using /lib/modules/2.4.2
1-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.21-dbox2/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.21-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.21-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.21-dbox2/misc/saa7126.o
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [](pos. 1).
Using /lib/modules/2.4.21-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.21-dbox2/misc/dvb_demux.o
Using /lib/modules/2.4.21-dbox2/misc/dvbdev.o
Using /lib/modules/2.4.21-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
Using /lib/modules/2.4.21-dbox2/misc/avia.o
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
Using /lib/modules/2.4.21-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.21-dbox2/misc/dmxdev.o
Using /lib/modules/2.4.21-dbox2/misc/dvb_frontend.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.21-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.23.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.8.4.2 2003/07/22 08:01:56 alexw Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.139.2.1.2.5 2003/06/04 11:04:45 alexw Exp $
avia_gt_dmx: No firmware found at /var/tuxbox/ucodes/ucode.bin, using compiled-i
n version.
avia_gt_dmx: Successfully loaded ucode V0.14
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.25.4.4 2003/07/22 08:01:56 alexw Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.19.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.21-dbox2/misc/dvb.o
dvb.c: init_dvb
Init VES1893
Using /lib/modules/2.4.21-dbox2/misc/ves1893.o
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
VES1893: attaching VES1893 at 0x10 to adapter
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.141.2.1.2.1 2003/02/18 14:32:46 alexw Exp
$
avia_gt_napi: hardware section filtering enabled.
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.17.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.38.4.6 2003/07/22 08:01:56 alexw Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.12.4.1 2003/02/18 14:32:46 alexw Exp $
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.4 2002/08/22 13:39:33 Jolt Exp $
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.4 2003/07/22 08:33:41 alexW Exp $
$Id: sectionsd.cpp,v 1.167 2003/06/18 12:19:23 alexw Exp $
caching 504 hours
events are old 60min after their end time
$Id: zapit.cpp,v 1.290.2.50 2003/06/13 10:53:15 digi_casi Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
$Id: controld.cpp,v 1.107 2003/06/26 05:08:58 alexw Exp $
[controld] Boxtype detected: (1)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.477 2003/07/16 08:58:13 thegoodguy E
xp $
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[sectionsd] getUTC: read: Connection timed out
-
mash4077
- Tuxboxer
- Beiträge: 4654
- Registriert: Samstag 27. April 2002, 13:19
-
DieMade
- Oberlamer, Administrator & Supernanny
- Beiträge: 10532
- Registriert: Samstag 13. Juli 2002, 10:49
-
krusius
- Neugieriger
- Beiträge: 7
- Registriert: Sonntag 1. Januar 2006, 14:30
hallo,
habe heute was in der bootlog meiner philips box gegenüber der nokia box entdeckt!
auszug aus der bootlog der philips box:
CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
auszug aus der bootlog der nokia box:(roter Text)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
übersetzt: warnung cpu kern hat silicon wanzen--überprüfen sie die fehler
ist diese meldung bei den nokia boxen normal, oder ist dieses schuld daran, das die box keine sender findet.
wenn ja, wie kann man diesen fehler beheben
danke
krusius
habe heute was in der bootlog meiner philips box gegenüber der nokia box entdeckt!
auszug aus der bootlog der philips box:
CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
auszug aus der bootlog der nokia box:(roter Text)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
übersetzt: warnung cpu kern hat silicon wanzen--überprüfen sie die fehler
ist diese meldung bei den nokia boxen normal, oder ist dieses schuld daran, das die box keine sender findet.
wenn ja, wie kann man diesen fehler beheben
danke
krusius
-
sgd02
- Neugieriger
- Beiträge: 12
- Registriert: Sonntag 2. Januar 2005, 16:01
Hallo,
habe so ein ähnliches Problem siehe da http://forum.tuxbox-cvs.sourceforge.net ... hp?t=39919
Hab auch alles durchgemessen und überall sind die Spannugen vorhanden.
Wäre schön wenn da jemand noch ne Idee hätte.
Gruß
sgd02
habe so ein ähnliches Problem siehe da http://forum.tuxbox-cvs.sourceforge.net ... hp?t=39919
Hab auch alles durchgemessen und überall sind die Spannugen vorhanden.
Wäre schön wenn da jemand noch ne Idee hätte.
Gruß
sgd02
-
krusius
- Neugieriger
- Beiträge: 7
- Registriert: Sonntag 1. Januar 2006, 14:30
hallo,
also, habe jetzt bn2.01 drauf geflasht, doch die box bleibt bei premiere einen moment bitte im display und herzlich willkommen im fernseher stehen. (mit antennenanschluß)
ohne antenneanschluß kommt der fehlercode ud4.
habe im board schon mehr über dieses gelesen, doch da kam der fehlercode ud4 nach einer 1/2 std. oder so, mit antennenanschluß, aber bei mir steht das auch noch nach 5std.
weiß jemand mehr was das wieder sein kann?
hier noch eine bootlog
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-ef.50.04.07.00.00-d1
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/nokia-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/nokia-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/mpc8xx-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/mpc8xx-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/kernel/os in Flash-FS
debug: Got Block #0052
will verify ELF image, start= 0x800000, size= 1267512
verify sig: 0
Branching to 0x409b8
danke
krusius
also, habe jetzt bn2.01 drauf geflasht, doch die box bleibt bei premiere einen moment bitte im display und herzlich willkommen im fernseher stehen. (mit antennenanschluß)
ohne antenneanschluß kommt der fehlercode ud4.
habe im board schon mehr über dieses gelesen, doch da kam der fehlercode ud4 nach einer 1/2 std. oder so, mit antennenanschluß, aber bei mir steht das auch noch nach 5std.
weiß jemand mehr was das wieder sein kann?
hier noch eine bootlog
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-ef.50.04.07.00.00-d1
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/nokia-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/nokia-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/mpc8xx-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/mpc8xx-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/kernel/os in Flash-FS
debug: Got Block #0052
will verify ELF image, start= 0x800000, size= 1267512
verify sig: 0
Branching to 0x409b8
danke
krusius