SAGEM Ton Problem

[PT-1]

Sagem 1x Intel BMon 1.2

Beide Scarts= Kein Ton
Optical Out (Licht is an) = Kein Ton
Chinch Outputs = Kein Ton
Verschiedene Ucodes = Kein Ton
Verschiedene Images = Kein Ton
Mal in die Box geschaut ob man irgend etwas sieht = nichts
Verbinde Box mit PC und streame MP3 und Video zur Box= Kein Ton

Verbinde Box mit PC und streame zum PC = SOUND!

Irgend welche Info's

PT-1

[hannebamb(el)]

das kann von "defektes Scart-Kabel" bis zu ..... alles mögliche sein.

Mach bitte nen Boot-log und dann kann man evtl. sehen, ob ein Hardware-defekt vorliegt. Das beim PC dann was rauskommt ist OK, du schiebst ja nur digitale Daten durch das Netzwerkkabel

[DieMade]

Avia-Dekoder oder CXA (50:50 Joker *g*).

Edit: bei MP3 ja auch kein Ton - da scheidet der MPEG-Dekoer schon wieder aus und es bleibt eigentlich nur der CXA oder die GFX/Mixer Engine vom eNX.

Kein Ton am optischen Ausgang könnte aber auch wieder der AVIA600 sein, ziemlich seltsames Fehlerbild

[PT-1]

debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-52.97.8a.07.00.00-23
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040

will verify ELF image, start= 0x800000, size= 156828
verify sig: 263
Branching to 0x40000


U-Boot 1.1.1 (TuxBox) (Oct 30 2004 - 13:18:13)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load complete: 613263 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 613199 Bytes = 598.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (vom Jtg-Team) (gcc version 3.3.5) #2 Fri Oct 29 22:
09:59 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=cramfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30900k available (1040k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3a:29:41
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit mode
Intel/Sharp Extended Query Table at 0x0031
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x006a0000 : "root (cramfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.94 2004/07/03 01:18:36 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
Using /lib/modules/2.4.27-dbox2/misc/at76c651.o
DVB: registering frontend 0:0 (Atmel AT76C651A with TUA6010XS)...
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.202 2004/06/24 00:26:58 carjay Exp $
jtginfo $Id: jtginfo.c,v 1.1 2004/05/31 16:00:30 jtgriker Exp $
$Id: sectionsd.cpp,v 1.179 2004/09/10 11:36:00 thegoodguy Exp $
caching 504 hours
events are old 180min after their end time
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
$Id: zapit.cpp,v 1.357 2004/10/27 16:08:42 lucgas Exp $
/var/tuxbox/config/zapit/services.xml: No such file or directory
[camd] ca system id: 1722
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

[controld] Boxtype detected: (3, Sagem D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[english.locale] missing entry: EPGPlus.actions
[english.locale] missing entry: EPGPlus.bybouquet_mode
[english.locale] missing entry: EPGPlus.bypage_mode
[english.locale] missing entry: EPGPlus.change_font_size
[english.locale] missing entry: EPGPlus.change_font_style
[english.locale] missing entry: EPGPlus.change_size
[english.locale] missing entry: EPGPlus.channelentry_font
[english.locale] missing entry: EPGPlus.channelentry_separationlineheight
[english.locale] missing entry: EPGPlus.channelentry_width
[english.locale] missing entry: EPGPlus.channelevententry_font
[english.locale] missing entry: EPGPlus.edit_fonts
[english.locale] missing entry: EPGPlus.edit_sizes
[english.locale] missing entry: EPGPlus.font_style_bold
[english.locale] missing entry: EPGPlus.font_style_italic
[english.locale] missing entry: EPGPlus.font_style_regular
[english.locale] missing entry: EPGPlus.footer_fontbouquetchannelname
[english.locale] missing entry: EPGPlus.footer_fontbuttons
[english.locale] missing entry: EPGPlus.footer_fonteventdescription
[english.locale] missing entry: EPGPlus.footer_fonteventshortdescription
[english.locale] missing entry: EPGPlus.header_font
[english.locale] missing entry: EPGPlus.horgap1_height
[english.locale] missing entry: EPGPlus.horgap2_height
[english.locale] missing entry: EPGPlus.next_bouquet
[english.locale] missing entry: EPGPlus.options
[english.locale] missing entry: EPGPlus.page_down
[english.locale] missing entry: EPGPlus.page_up
[english.locale] missing entry: EPGPlus.prev_bouquet
[english.locale] missing entry: EPGPlus.reset_settings
[english.locale] missing entry: EPGPlus.save_settings
[english.locale] missing entry: EPGPlus.select_font_name
[english.locale] missing entry: EPGPlus.settings
[english.locale] missing entry: EPGPlus.slider_width
[english.locale] missing entry: EPGPlus.swap_mode
[english.locale] missing entry: EPGPlus.timeline_fontdate
[english.locale] missing entry: EPGPlus.timeline_fonttime
[english.locale] missing entry: EPGPlus.vergap1_width
[english.locale] missing entry: EPGPlus.vergap2_width
[english.locale] missing entry: EPGPlus.view_mode
[english.locale] missing entry: flashupdate.proxypassword_hint2
[english.locale] missing entry: movieplayer.pesplayback
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
hintbox: found string No channels were found!
hintbox: found string Please execute a scan
hintbox: found string (dbox-key -> service)
[sectionsd] getUTC: read: Connection timed out

[hannebamb(el)]

Hmmm,
das ist der Log eines Images im jungfräulichen Zustand, d.h. ohne, das der Fall von mit oder ohne Ton aufgetreten sein kann.

....
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
$Id: zapit.cpp,v 1.357 2004/10/27 16:08:42 lucgas Exp $
/var/tuxbox/config/zapit/services.xml: No such file or directory
[camd] ca system id: 1722
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
....

das scheint mir ein wenig alt zu sein. Bin mir jetzt aber auch nicht sicher, was jtg in seinen Images nutzt vom release Stand her. Vielleicht fragst du dort noch mal nach.

Kannst du das Image mal einrichten (Senderscan) und evtl. mal schalten.
Vielleicht kann man dann ersehen, wo das Problem liegen könnte.