Umschalten von neutrino auf enigma

[boesedarling]

Eigentlich sollte das Umschalten von Neutrino auf enigma doch beim booten möglich sein. Ich habe das neueste Yagi iMAGE 1.92, neutrino funkt. gut, doch wenn ichauf Enigma schalte stürzt die box beim booten ab und fängt von vorne an.

[mash4077]

Hi,

ich gehe mal davon aus, dass Du das YAD-Image v1.9.0.2 meinst. Ich nutze dies zurzeit ebenfalls auf einer meiner Boxen. Enigma läuft, soweit man das von Enigma sagen kann, bei mir.

Poste mal ein Log!

Gruß
mash

[boesedarling]

Using /lib/modules/2.4.26-dbox2/misc/saa7126.o
Detected STB:
Vendor: Sagem
Model: D-BOX2
Using /lib/modules/2.4.26-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.26-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.26-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.26-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.26-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.26-dbox2/misc/avia_av.o
route: SIOC[ADD|DEL]RT: Network is unreachable
avia_av: $Id: avia_av_core.c,v 1.94 2004/07/03 01:18:36 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.26-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.38 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.26-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.26-dbox2/misc/at76c651.o
Using /lib/modules/2.4.26-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1993)...
Using /lib/modules/2.4.26-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.202 2004/06/24 00:26:58 carjay Exp $
/etc/init.d/rcS: 154: cannot create /etc/issue.net: No space left on device
Using /lib/modules/2.4.26-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.4 2004/07/16 21:54:30 mogway Exp $
Yadi Snapshot vom 07.08.2004 21:45 - Image-Version 1.9.0.2
Networkcfg eth0: 192.168.53.2/255.255.255.0 gw 192.168.0.1
Startmode: Bootmenu - SPTS:off - HWS:on
Using /lib/modules/2.4.26-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.26-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.26-dbox2/kernel/fs/cifs/cifs.o
Starting pid 89, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. [LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[ConfigFile] Unable to open file /var/tuxbox/config/lcdmenu.conf for writing.
chmod: /var/bin/camd2: No space left on device
[camd] ca system id: 1702
mv: unable to rename `/var/tuxbox/config/enigma/registry': No such file or direc
tory
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
sh: cannot open /share/keymaps/eng.kmap: No such file
Segmentation fault
Starting pid 127, console /dev/console: '/bin/switch'
CXA2126 found
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-a7.e4.06.08.00.00-0d
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040

will verify ELF image, start= 0x800000, size= 153208
verify sig: 263
Branching to 0x40000


U-Boot 1.1.1 (TuxBox) (Aug 7 2004 - 22:26:37)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (jffs2) loading 'vmlinuz' to 0x100000
Scanning JFFS2 FS: . .
### FS load complete: 614430 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 614366 Bytes = 600 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.26-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.4) #2 Sa Aug 7
23:09:46 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock3 rootfstype=squashfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30896k available (1044k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:33:02:a1
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit mode
Intel/Sharp Extended Query Table at 0x0031
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x000e0000 : "kernel (jffs2)"
0x000e0000-0x006a0000 : "root (squashfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'0) multi-
Using /lib/modules/2.4.26-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.26-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.26-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.26-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.26-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.26-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.26-dbox2/misc/avs.o
Using /lib/modules/2.4.26-dbox2/misc/saa7126.o
Detected STB:
Vendor: Sagem
Model: D-BOX2
Using /lib/modules/2.4.26-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.26-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.26-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.26-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.26-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.26-dbox2/misc/avia_av.o
route: SIOC[ADD|DEL]RT: Network is unreachable
avia_av: $Id: avia_av_core.c,v 1.94 2004/07/03 01:18:36 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.26-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.38 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.26-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.26-dbox2/misc/at76c651.o
Using /lib/modules/2.4.26-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1993)...
Using /lib/modules/2.4.26-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.26-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.202 2004/06/24 00:26:58 carjay Exp $
/etc/init.d/rcS: 154: cannot create /etc/issue.net: No space left on device
Using /lib/modules/2.4.26-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.4 2004/07/16 21:54:30 mogway Exp $
Yadi Snapshot vom 07.08.2004 21:45 - Image-Version 1.9.0.2
Networkcfg eth0: 192.168.53.2/255.255.255.0 gw 192.168.0.1
Startmode: Bootmenu - SPTS:off - HWS:on
Using /lib/modules/2.4.26-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.26-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.26-dbox2/kernel/fs/cifs/cifs.o
Starting pid 89, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console.

[mash4077]

/etc/init.d/rcS: 154: cannot create /etc/issue.net: No space left on device
[ConfigFile] Unable to open file /var/tuxbox/config/lcdmenu.conf for writing.
chmod: /var/bin/camd2: No space left on device
[camd] ca system id: 1702
mv: unable to rename `/var/tuxbox/config/enigma/registry': No such file or directory
sh: cannot open /share/keymaps/eng.kmap: No such file
Segmentation fault
/etc/init.d/rcS: 154: cannot create /etc/issue.net: No space left on device

Flash voll!?

Flash mal neu...

Gruß
mash

[boesedarling]

Vielen Dank Mash, hat funktioniert.