flfs

Beitrag von **Xynuerz** » Samstag 22. Mai 2004, 13:18

hab nun die rcS geändert und modprobe in insmode geändert aber da stimmt immer noch was nciht es scheint wahrhaftig nur was an der rcS zu liegen

Code: Alles auswählen

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID dd    gtxID 0b
debug: fpID 5a     dsID 01-ee.8a.1f.07.00.00-a9
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0028

will verify ELF image, start= 0x800000, size= 143000
verify sig: 262
Branching to 0x40000


U-Boot 0.4.0 (TuxBox) JFFS2 only (Aug 15 2003 - 16:44:21)

CPU:   PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBox2, Nokia --       Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
LCD:   ready
FB:    ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET
Scanning JFFS2 FS: ...... done.

### FS (jffs2) loading 'var/tuxbox/boot/logo-lcd'
### FS (jffs2) loading 'var/tuxbox/boot/logo-fb'
### FS (jffs2) loading 'var/tuxbox/boot/ppcboot.conf'
### FS (jffs2) loading 'var/tuxbox/boot/u-boot.conf'
### FS (jffs2) loading 'vmlinuz'
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
   Image Name:   dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    602377 Bytes = 588.3 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.25-dbox2 (root@Knoppix) (gcc version 3.3.3) #1 Sa Mai 22 12:16
:33 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rw console=ttyS0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30924k available (1020k kernel code, 364k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1a:f9:d9
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x00800000 : "root (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cramfs: wrong magic
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 11, console /dev/console: '/etc/init.d/rcS') multi-c
Using /lib/modules/2.4.25-dbox2/misc/tuxbox.o
Detected STB:
  Vendor: Nokia
  Model: D-BOX2 
Using /lib/modules/2.4.25-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.25-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
insmod: unresolved symbol event_write_message
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_input.o
insmod: unresolved symbol dbox2_fp_queue_alloc
insmod: unresolved symbol fp_sendcmd
insmod: unresolved symbol fp_get_i2c
insmod: unresolved symbol fp_cmd
insmod: unresolved symbol dbox2_fp_queue_free
Using /lib/modules/2.4.25-dbox2/misc/ves1820.o
Using /lib/modules/2.4.25-dbox2/misc/ves1x93.o
Using /lib/modules/2.4.25-dbox2/misc/avs.o
insmod: unresolved symbol event_write_message
Using /lib/modules/2.4.25-dbox2/misc/saa7126.o
Using /lib/modules/2.4.25-dbox2/misc/cam.o
insmod: unresolved symbol dbox2_fp_reset_cam
Using /lib/modules/2.4.25-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.25-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_av_set_stc
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_v4l2.o
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
Using /lib/modules/2.4.25-dbox2/misc/avia_av.o
insmod: unresolved symbol dbox2_fp_reset
insmod: unresolved symbol event_write_message
Using /lib/modules/2.4.25-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: registering frontend 0:0 (VES1893)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.25-dbox2/misc/cam_napi.o
insmod: unresolved symbol cam_poll
insmod: unresolved symbol cam_read_message
insmod: unresolved symbol cam_reset
insmod: unresolved symbol cam_write_message
Using /lib/modules/2.4.25-dbox2/misc/avia_av_napi.o
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_accel_crc32
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_napi.o
insmod: unresolved symbol dbox2_fp_sec_diseqc_cmd
insmod: unresolved symbol dbox2_fp_sec_set_tone
insmod: unresolved symbol dbox2_fp_sec_set_voltage
insmod: unresolved symbol dbox2_fp_tuner_write_qam
insmod: unresolved symbol dbox2_fp_sec_set_power
insmod: unresolved symbol dbox2_fp_tuner_write_qpsk
insmod: unresolved symbol dbox2_fp_sec_set_high_voltage
Starting pid 68, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. /dev/input/event0: No such file or 
directory

Beitrag von **wittinobi** » Samstag 22. Mai 2004, 14:04

nimm einfach mal diese rcs.
die ist aber nicht von mir.
kommt von nem freundlichen helfer aus nem anderen board.

Code: Alles auswählen

#!/bin/sh

PATH=/sbin:/bin
CAMALPHA="firmware=/var/tuxbox/ucodes/cam-alpha.bin"
UCODE="ucode=/var/tuxbox/ucodes/ucode.bin"
hostname -F /etc/hostname
mount -a
ifup -a
test -x /sbin/inetd && inetd
 ./etc/profile
insmod tuxbox


VENDOR=`/bin/tuxinfo -V`
VENDOR_ID=`/bin/tuxinfo -v`
MODEL=`/bin/tuxinfo -M`
MODEL_ID=`/bin/tuxinfo -m`
SUBMODEL=`/bin/tuxinfo -S`
SUBMODEL_ID=`/bin/tuxinfo -s`

echo "Detected STB:"
echo "  Vendor: $VENDOR"
echo "  Model: $MODEL $SUBMODEL"
#

insmod dvb-core dvb_shutdown_timeout=0

# D-BOX2
if [ $MODEL_ID -eq 1 ]; then

	# I2C core
	insmod dbox2_i2c
	insmod dvb_i2c_bridge

	#
	insmod event

	# Frontprozessor
	insmod dbox2_fp
	insmod dbox2_fp_input

	# Frontends
	# Nokia
	if [ $VENDOR_ID -eq 1 ]; then
		insmod ves1820
		insmod ves1x93 board_type=1
	# Philips
	elif [ $VENDOR_ID -eq 2 ]; then
		insmod tda8044h
	# Sagem
	elif [ $VENDOR_ID -eq 3 ]; then
		insmod at76c651
		insmod ves1x93 board_type=2
	fi

	# Misc IO
	insmod avs
	insmod saa7126
	# Philips
	if [ $VENDOR_ID -eq 2 ]; then
		insmod cam mio=0xC040000 $CAMALPHA
	else
		insmod cam mio=0xC000000 $CAMALPHA
	fi
	insmod lcd

	# A/V
	insmod avia_napi
	insmod avia_av firmware=/var/tuxbox/ucodes
	if [ -e /var/etc/.hw_sections ]; then
	insmod avia_gt $UCODE hw_sections=0
	else
	insmod avia_gt $UCODE 
	fi
	insmod avia_gt_fb console_transparent=1
	insmod avia_gt_lirc
	insmod avia_gt_oss
	insmod avia_gt_v4l2

	insmod cam_napi
	insmod avia_av_napi
	if [ -e /var/etc/.spts_mode ]; then
	insmod avia_gt_napi mode=1
	else
	insmod avia_gt_napi
	fi
	insmod dbox2_fp_napi

fi
insmod dvb2eth
echo "$VENDOR $MODEL - Kernel %r (%t)." > /etc/issue.net
# compatibility links
ln -sf demux0 /dev/dvb/adapter0/demux1
ln -sf dvr0 /dev/dvb/adapter0/dvr1
ln -sf fb/0 /dev/fb0

test -x /bin/loadkeys && loadkeys /share/keymaps/i386/qwertz/de-latin1.kmap.gz
if [ -e /etc/init.d/rcS.local ]; then
	. /etc/init.d/rcS.local
fi

damit sollte dann alles funzen.
an dieser stelle auch nochmals ein dank an body ,von dem die rcs stammt.

mfg
wittinobi

Beitrag von **Xynuerz** » Samstag 22. Mai 2004, 15:03

ich werde mein glück versuchen

thx vor erst einmal für eure hilfe

Beitrag von **Xynuerz** » Samstag 22. Mai 2004, 23:29

Dicken Dank an euch dir mir heir geholfen habt

image rennt nun 1 a

hab mir dann mal die camd2 von ditmarh gezogen eingebaut und meine pw karte funktioniert auch find ich jut

THX noch mal

Beitrag von **Jake** » Sonntag 23. Mai 2004, 08:57

Alternativ kannst Du auch in cdk/Patches/busybox-flash.config und/oder cdk/Patches/busybox.config
# CONFIG_MODPROBE is not set
in
CONFIG_MODPROBE=y
umändern. Dann kannst Du auch die normale rcS verwenden.

Welche der beiden Konfig-Dateien verwendet wird, weiß ich nicht, ich habe einfach beide geändert und gut.