Das bootlog hab ich nicht gepostet, weil ich dachte das es nichts bringt, da es während des fehlers keine daten ausspuckt.
Nochmal zur Erinnerung:
Nun mein log:Gut dann mal schritt für schritt:
Also die dbox läuft schon ne weile, nun schalte ich sie komplett aus (kein standby). wenn ich sie nun wieder starten will blinkt das display kurz auf, nun müßte dieser erste bildschirm auf dem display erscheinen, tut er aber nicht. Stattdessen wird das display komplett schwarz (auch die gelbe leucht leuchtet nicht mehr). Ich versuche nun weitere resets und mit glück bootet sie nach dem 20. mal wieder normal. Den gleichen effekt hat es wenn ich sie zehn minuten in Ruhe lasse, dann bootet sie in der regel auch normal.
Hab ne Nokia Sat Box
Image spielt keine rolle, weil es immer passiert. Hab immoment alexW 1.6.9 und neuste cramfs drauf
xdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-47.98.e0.06.00.00-dc
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
will verify ELF image, start= 0x800000, size= 146452
verify sig: 262
Branching to 0x40000
U-Boot 0.4.0 (TuxBox) (Jul 21 2003 - 20:18:06)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load complete: 640967 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 640903 Bytes = 625.9 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.21-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Jul 6 12:22:55 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30804k available (1128k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:10:7c:9f
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'Using /lib/modules/2.4.2
1-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.21-dbox2/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
SIOCADDRT: Invalid argument
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.21-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.21-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.21-dbox2/misc/saa7126.o
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [](pos. 1).
Using /lib/modules/2.4.21-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.21-dbox2/misc/dvb_demux.o
Using /lib/modules/2.4.21-dbox2/misc/dvbdev.o
Using /lib/modules/2.4.21-dbox2/misc/avia.o
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
Using /lib/modules/2.4.21-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.21-dbox2/misc/dmxdev.o
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.21-dbox2/misc/dvb_frontend.o
Using /lib/modules/2.4.21-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.23.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.8.4.2 2003/07/22 08:01:56 alexw Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.139.2.1.2.5 2003/06/04 11:04:45 alexw Exp $
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.25.4.4 2003/07/22 08:01:56 alexw Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.19.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.21-dbox2/misc/dvb.o
dvb.c: init_dvb
Init VES1893
Using /lib/modules/2.4.21-dbox2/misc/ves1893.o
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
VES1893: attaching VES1893 at 0x10 avia_gt_core: masking unhandled irq reg 0 bit
6
to adapter
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.141.2.1.2.1 2003/02/18 14:32:46 alexw Exp
$
avia_gt_napi: hardware section filtering disabled.
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.17.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.38.4.6 2003/07/22 08:01:56 alexw Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.12.4.1 2003/02/18 14:32:46 alexw Exp $
Using /lib/modules/2.4.21-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.4 2002/08/22 13:39:33 Jolt Exp $
CXA2092 found
CXA2092 found
Using /lib/modules/2.4.21-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
cdkVcInfo $Id: cdkVcInfo.c,v 1.4 2003/07/22 08:33:41 alexW Exp $
$Id: sectionsd.cpp,v 1.167 2003/06/18 12:19:23 alexw Exp $
caching 504 hours
events are old 60min after their end time
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.290.2.50 2003/06/13 10:53:15 digi_casi Exp $
[camd] ca system id: 1702
[camd] card_country: GER
[camd] card_number: 8003284657
[camd] card_version: 0384
[camd] no card is in slot #2
[camd] a card is in slot #1
$Id: controld.cpp,v 1.107 2003/06/26 05:08:58 alexw Exp $
[controld] Boxtype detected: (1)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.477 2003/07/16 08:58:13 thegoodguy E
xp $
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[basicsocket] send_data: Resource temporarily unavailable
[CFrontend::getEvent] FE_COMPLETION_EV: freq 1470500
open: No such file or directory
[camd] starting onid 0085 sid 000f
[neutrino] initialized everything
descramble onid: 0085 sid: 000f status: 8484
dmxdev: buffer overflow
[sectionsd] readNbytes: received POLLERR
Kenn mich mit dem log nicht so aus, vielleicht fällt ja jemanden was ungewöhnliches auf.
Thx im Voraus
)
)