ich habe einen Nokia Dbox 2 SAT (2xintel Bmon 1.2) dieser bleibt bei "Starting Kernel"immer stehen wenn ich länger warte dann verschwindet das NEUTRINO LOGO vom Display und es steht nur noch unten im Display "starting Kernel".
Habe es mit älteren images versucht da sieht man beim neu booten nicht auf em Display. Bei Alexw 1.6.9 kommt "starting Kernel" und nichts weiter. Was mir ebenfalls aufgefallen ist ist folgendes. Wenn ich den Strcker einstecke sehe ich manchmal im display den Debug mode aber sehr oft sieht man nichts es springt also direkt zum starten.
Also Images einspielen geht nur es bootet halt bis zur oben genannten stelle. Hier habe ich zwei LOGS.
Habe dies mit der Einstellung "Backup der orig. Software" beim Bootmanager ausgelesen. Ist dies korreckt ??
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID xx.xx.xx.xx.xx.xx.xx.xx (editiert von mir)
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Mar 13 2003 - 12:11:32)
CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
. LCD: find_inode failed for name=tuxbot
load: Failed to find inode
ready - can't find logo in flash
FB: find_inode failed for name=boob
load: Failed to find inode
can't find logo in flash - no init
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 571677 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 571613 Bytes = 558 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-f7.fa.5f.07.00.00-e9
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Mar 13 2003 - 12:11:32)
CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
. find_inode failed for name=boob
load: Failed to find inode
LCD: find_inode failed for name=tuxbon
load: Failed to find inode
ready - can't find logo in flash
FB: find_inode failed for name=tuxbot
load: Failed to find inode
can't find logo in flash - no init
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 571677 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 571613 Bytes = 558 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Apr 13 14:50:18 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 251625000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30964k available (996k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
devfs_register(vc/12): could not append to parent, err: -17
CPM UART driver version 0.03
_devfs_prepare_leaf(tts/0): could not create parent path
devfs_register(tts/0): could not prepare leaf
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
devfs_register(pty/m8): could not append to parent, err: -17
devfs_register(pty/m9): could not append to parent, err: -17
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:43:1b:04
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Cannot open root device "/dev/mtdblock2" or 00:00
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on 00:00
<0>Rebooting in 180 seconds..
und das zweite LOG sieht folgendermaßen aus:
0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 571677 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 571613 Bytes = 558 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... }debug: DDF: Calibrating delay loop... debug:
DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID xx.xx.xx.xx.xx.xx.xx (edit von mir)
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.2, My IP 192.168.0.5
debug: Sending TFTP-request for file C/dbox2/auslesen/image_backup/tftpboot/ppcb
oot
will verify ELF image, start= 0x800000, size= 224356
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
ppcboot 0.6.4 (Jan 10 2002 - 16:35:20)
Initializing...
CPU: PPC823ZTnnB2 at 67 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-43-1b-04
FLASH: 8 MB
LCD driver (KS0713) initialized
No LCD Logo in Flash , trying tftp
BOOTP broadcast 1
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'C/dbox2/auslesen/image_backup/tftpboot/logo-lcd'.
Load address: 0x130000
Loading: ##
LCD logo at: 0x130000 (0x1FD2864 bytes)
No FB Logo in Flash , trying tftp
BOOTP broadcast 1
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'C/dbox2/auslesen/image_backup/tftpboot/logo-fb'.
Load address: 0x120000
Loading: ###
FB logo at: 0x0 (0x1FC0000 bytes)
AVIA Frambuffer
Input: serial
Output: serial
Images:
1: cdk
2: yadd
3: debian
4: tiab
5: flash
Select image (1-5), other keys to stop autoboot: 0
BOOTP broadcast 1
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'C/dbox2/auslesen/image_backup/tftpboot/kernel-cdk'.
Load address: 0x100000
Loading: ##################################################
#####################
###############################################
## Booting Linux kernel at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 600241 Bytes = 586 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.2 (root@noer-lab.noernet.de) (gcc version 3.0.1 20010702 (prer
elease)) #89 Fri Aug 24 21:37:54 CEST 2001
Boot arguments: console=ttyS0 root=/dev/nfs rw nfsroot=192.168.0.2:C/dbox2/ausle
sen/image_backup/cdkroot/
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/nfs rw nfsroot=192.168.0.2:C/dbox2/
auslesen/image_backup/cdkroot/
time_init: decrementer frequency = 251250000/60
Warning: real time clock seems stuck!
Console: colour dummy device 80x25
Calibrating delay loop... 66.56 BogoMIPS
Memory: 30624k available (1088k kernel code, 424k data, 64k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
devfs: devfs_register(): device already registered: "vc/16"
devfs: devfs_register(): device already registered: "vc/17"
devfs: devfs_register(): device already registered: "vc/23"
devfs: devfs_register(): device already registered: "vc/24"
devfs: devfs_register(): device already registered: "vc/35"
devfs: devfs_register(): device already registered: "vc/36"
devfs: devfs_register(): device already registered: "vc/37"
devfs: devfs_register(): device already registered: "vc/38"
devfs: devfs_register(): device already registered: "vc/39"
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
devfs: devfs_register(): device already registered: "pty/m2"
pty: 256 Unix98 ptys configured
block: queued sectors max/low 20250kB/6750kB, 64 slots per queue
eth0: CPM ENET Version 0.2, 00:50:9c:43:1b:04
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x000c0000 : "idxfs"
0x000c0000-0x001c0000 : "var"
0x001c0000-0x00760000 : "root"
0x00760000-0x00800000 : "flfs"
0x00020000-0x00800000 : "GesamteFlashOhneBL"
0x007e0000-0x00800000 : "flfs_128"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Sending BOOTP requests....... OK
IP-Config: Got BOOTP answer from 192.168.0.2, my address is 192.168.0.5
IP-Config: Guessing netmask 255.255.255.0
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Looking up port of RPC 100003/2 on 192.168.0.2
RPC: sendmsg returned error 101
portmap: RPC call returned error 101
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/2 on 192.168.0.2
RPC: sendmsg returned error 101
portmap: RPC call returned error 101
Root-NFS: Unable to get mountd port number from server, using default
RPC: sendmsg returned error 101
mount: RPC call returned error 101
Root-NFS: Server returned error -101 while mounting C/dbox2/auslesen/image_backu
p/cdkroot/
VFS: Unable to mount root fs via NFS, trying floppy.
request_module[block-major-2]: Root fs not mounted
VFS: Cannot open root device "nfs" or 02:00
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on 02:00
Rebooting in 180 seconds..
gruß vedo