Umbau Kabel -> SAT

[Chucky]

Hallo,

was ist notwendig um aus einer Kabel- eine Sat-Box zu machen? Geht das und wenn ja, was kostet mich der Spaß circa?

Mein alter Herr will von Kabel auf Sat umstellen und würde gerne seine box nutzen.

Achja, ist eine Nokia.

Danke schonmal!

[Zahni]

Wurde auch schon x-mal gefragt.

Kurz und knapp: Nein, geht nicht.

Alte Box bei ebay verticken und da eine Satbox holen (z.B.)

-Zahni

[Chucky]

Hatte die Suche ja befragt, aber nichts hilfreiches gefunden.

Ich war immer der Meinung, dass lediglich der Tuner anders ist und den müsste man doch tauschen können !?

eBay wäre möglich, aber er (ich) möchte gerne die Nokia behalten. Wenn ich den Preisunterschied zwischen Kabel und Sat sehe, müsste ein Umbau doch rentabel sein.

Wenn Du sagst es ist unmöglich, glaube ich Dir

[kolp]

technisch möglich ist es schon, aber eben unrentabel- fachchinesisch "unökonomisch".

ein sattuner allein kostet über 100 euro.

gruss aus ffm

[SoLaLa]

nur bei Sagems geht das ziemlich Problemlos, da müssen n paar Bauteile nachgerüstet werden, aber das ist kleinkram

[mash4077]

nur bei Sagems geht das ziemlich Problemlos, da müssen n paar Bauteile nachgerüstet werden, aber das ist kleinkram

Hast Du das schon mal gemacht?
Oder ist das reine Theorie?

Gruß
mash

[SoLaLa]

hallo Leute,
also ich bin eine Original Sagem Kabel dBox2, schwarz,
und noch verdammt neu (mit Schutzfolie auf dem Display)
mein Eigentümer wollte mich schon verschrotten da ich leider einen Haufen
zerstörter Leiterbahnen an meinem 1xi Flash aufwies und außerdem keinen
Frontprozessor mehr besaß. Gottseidank hat er sich besonnen und mich mit
mit nem (halbwegs funktionierenden) Frontprozessor und restaurierten
Leiterbahnen wieder zum Leben erweckt. Großzügigerweise bekam ich auch noch
eine Sockelleiste für das Frontend...


debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-a7.2e.09.08.00.00-08
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0052

will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Mar 13 2003 - 12:09:31)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 641754 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 641690 Bytes = 626 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Fre Apr 11 11:35:47 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30796k available (1132k kernel code, 380k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:31:78:aa
Linux video capture interface: v1.00
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 9, console /dev/console: '/etc/init.d/rcS') multi-ca
Using /lib/modules/2.4.20-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.20-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.20-dbox2/misc/dvb-core.o
SIOCADDRT: Invalid argument
ifup: Ignoring unknown interface net
ifup: Ignoring unknown interface loopback
Using /lib/modules/2.4.20-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter PowerPC 8xx I2C adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20-dbox2/misc/dbox2_fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [PowerPC
8xx I2C adapter](pos. 0).
Using /lib/modules/2.4.20-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.20-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Using /lib/modules/2.4.20-dbox2/misc/saa7126.o
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 2).
Using /lib/modules/2.4.20-dbox2/misc/lcd.o
Using /lib/modules/2.4.20-dbox2/misc/cam.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.22 2003/01/14 10:26:36 jolt Exp $
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [PowerPC 8xx I2C adapter](p
os. 3).
CAM: attached to adapter PowerPC 8xx I2C adapter
Using /lib/modules/2.4.20-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.20-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.12 2003/01/18 00:52:35 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [dvb] registered to adapter [PowerPC 8xx I2C adapter](pos. 4)
.
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.20-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.5 2003/01/14 08:43:17 jolt Exp $
Using /lib/modules/2.4.20-dbox2/misc/dbox2_fp_napi.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.20-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.62 2003/05/11 02:42:58 obi Exp $
avia_av_event: $Id: avia_av_event.c,v 1.6 2003/04/17 07:29:48 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.5 2003/04/17 07:29:48 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.35 2003/04/14 00:13:10 obi Exp $
avia_gt_core: autodetecting chip type... AViA eNX found
avia_gt_enx: $Id: avia_gt_enx.c,v 1.17 2003/04/14 00:13:10 obi Exp $
write 1 event's ...
write 1 event's ...
avia_gt_accel: $Id: avia_gt_accel.c,v 1.15 2003/01/14 23:59:32 jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.173 2003/05/11 02:42:59 obi Exp $
avia_gt_dmx: Successfully loaded ucode vB107
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.31 2003/04/14 00:13:10 obi Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.23 2003/04/14 00:13:10 obi Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.27 2003/04/14 00:13:10 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.35 2003/04/14 00:13:10 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.23 2003/04/14 00:13:10 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.23 2003/04/25 05:27:09 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.45 2003/04/14 00:13:10 obi Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.7 2003/04/14 00:13:10 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.18 2003/04/17 07:29:48 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.8 2003/04/14 00:13:10 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/ves1x93.o
VES1x93 not found (identity 00)
Using /lib/modules/2.4.20-dbox2/misc/at76c651.o
DVB: registering frontend 0:0 (Atmel AT76c651(B) with DAT7021)...
Using /lib/modules/2.4.20-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.17 2003/04/17 07:29:48 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.180 2003/05/11 02:42:59 obi Exp $
cdkVcInfo $Id: cdkVcInfo.c,v 1.2.1 2003/03/13 15:11:22 alexW Exp $

$Id: sectionsd.cpp,v 1.166 2003/03/14 04:27:55 obi Exp $
caching 504 hours
events are old 60min after their end time
[camd] ca system id: 1702 <------ da steckt schon die SATkarte drin
$Id: zapit.cpp,v 1.312 2003/05/12 05:14:41 digi_casi Exp $
$Id: controld.cpp,v 1.106 2003/04/23 13:00:12 alexw Exp $

[controld] Boxtype detected: (3, Sagem D-BOX2)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.443 2003/05/13 07:03:06 digi_casi Ex
p $

[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[neutrino] initialized everything
[infoviewer] satellite = None
zap failed! <---- Kabel ist nicht angeschlossen


hier starte ich mal neu mit einem schönen aufgesteckten Sattuner.
Schade nur, daß meine Rückwand dafür entfernt werden muß:

debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-a7.2e.09.08.00.00-08
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0052

will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Mar 13 2003 - 12:09:31)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 641754 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 641690 Bytes = 626 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Fre Apr 11 11:35:47 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30796k available (1132k kernel code, 380k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:31:78:aa
Linux video capture interface: v1.00
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 9, console /dev/console: '/etc/init.d/rcS') multi-ca
Using /lib/modules/2.4.20-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.20-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.20-dbox2/misc/dvb-core.o
SIOCADDRT: Invalid argument
ifup: Ignoring unknown interface net
ifup: Ignoring unknown interface loopback
Using /lib/modules/2.4.20-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter PowerPC 8xx I2C adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20-dbox2/misc/dbox2_fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [PowerPC
8xx I2C adapter](pos. 0).
Using /lib/modules/2.4.20-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.20-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Using /lib/modules/2.4.20-dbox2/misc/saa7126.o
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 2).
Using /lib/modules/2.4.20-dbox2/misc/cam.o
Using /lib/modules/2.4.20-dbox2/misc/lcd.o
$Id: cam.c,v 1.22 2003/01/14 10:26:36 jolt Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [PowerPC 8xx I2C adapter](p
os. 3).
CAM: attached to adapter PowerPC 8xx I2C adapter
Using /lib/modules/2.4.20-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.20-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.12 2003/01/18 00:52:35 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [dvb] registered to adapter [PowerPC 8xx I2C adapter](pos. 4)
.
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.20-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.5 2003/01/14 08:43:17 jolt Exp $
Using /lib/modules/2.4.20-dbox2/misc/dbox2_fp_napi.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.20-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.62 2003/05/11 02:42:58 obi Exp $
avia_av_event: $Id: avia_av_event.c,v 1.6 2003/04/17 07:29:48 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.5 2003/04/17 07:29:48 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.35 2003/04/14 00:13:10 obi Exp $
avia_gt_core: autodetecting chip type... AViA eNX found
avia_gt_enx: $Id: avia_gt_enx.c,v 1.17 2003/04/14 00:13:10 obi Exp $
write 1 event's ...
write 1 event's ...
avia_gt_accel: $Id: avia_gt_accel.c,v 1.15 2003/01/14 23:59:32 jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.173 2003/05/11 02:42:59 obi Exp $
avia_gt_dmx: Successfully loaded ucode vB107
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.31 2003/04/14 00:13:10 obi Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.23 2003/04/14 00:13:10 obi Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.27 2003/04/14 00:13:10 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.35 2003/04/14 00:13:10 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.23 2003/04/14 00:13:10 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.23 2003/04/25 05:27:09 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.45 2003/04/14 00:13:10 obi Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.7 2003/04/14 00:13:10 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.18 2003/04/17 07:29:48 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.8 2003/04/14 00:13:10 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1993)... //tatsächlich... ein SATtuner
Using /lib/modules/2.4.20-dbox2/misc/at76c651.o
Using /lib/modules/2.4.20-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.17 2003/04/17 07:29:48 obi Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.180 2003/05/11 02:42:59 obi Exp $
cdkVcInfo $Id: cdkVcInfo.c,v 1.2.1 2003/03/13 15:11:22 alexW Exp $

$Id: sectionsd.cpp,v 1.166 2003/03/14 04:27:55 obi Exp $
caching 504 hours
events are old 60min after their end time
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.312 2003/05/12 05:14:41 digi_casi Exp $
$Id: controld.cpp,v 1.106 2003/04/23 13:00:12 alexw Exp $

[controld] Boxtype detected: (3, Sagem D-BOX2)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.443 2003/05/13 07:03:06 digi_casi Ex
p $

[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[neutrino] initialized everything
[infoviewer] satellite = Astra 19.2E
avia_av: video play (vpid=0x01FF)
avia_av: audio play (apid=0x0200)
[camd] starting onid 0085 sid 000a
descramble onid: 0085 sid: 000a status: 1d1d
avia_av_core.c: avia_av_interrupt: Reserved 01.
Diff: 5, Last-Diff: 1 Direction: 2, Gain: 50
Diff: 6, Last-Diff: 2 Direction: 2, Gain: 100
Diff: 7, Last-Diff: 3 Direction: 2, Gain: 150
write 1 event's ...
write event ... free found
write 1 event's ...
write event ... free found
write event ... filter ok
//und funktionieren tut er auch... Pearl Harbour läuft...

[kolp]

solala ist nun mal der beste....

glückwunsch und gruss aus ffm

[Rudi Ratlos 4711]

Muss eigentlich der FP Proz zum jeweiligen Tunertyp passen ? Und was muss alles nachbestückt werden ?

RR4711

[mash4077]

DVB: registering frontend 0:0 (VES1993)... //tatsächlich... ein SATtuner
//und funktionieren tut er auch... Pearl Harbour läuft...

Cool!

Bitte, bitte noch die Fragen von "RR4711" beantworten!

+ ist der Tuner z.B. käuflich zu erwerben?

Gruß
mash

[SoLaLa]

neben pins 1 bis 7 vom tuner (nun kommt mir nicht wieder mit "im Forum stehts aber andersrum"... pin1 ist das erste Lötauge vom Antennenanschluß aus betrachtet) sitzt ne Handvoll kleinkram. wahrscheinlich alles schon bestückt... wenn nicht, dann halt nachrüsten...
ob man den tuner irgednwo kaufen kann? k.A.... den tuner selbst vielleicht, aber das komplette Platinchen wohl eher nicht

[mash4077]

Vielen Dank für die Infos!

Kannst Du noch mal was zu der Frage mit dem Frontproz. sagen?

Gruß
mash