Tuner Hilfe

[Yellowfan]

Habe meine Nokia 2xAMD in den Debug gebracht und dabei ausversehen den XH3 Jumper mit der Masse verbunden.Die Box lief aber trotzdem noch,bis auf das sie keine Kanäle mehr empfangen hat.Beim Nachmessen fehlte die 12V an Pin7 vom Tuner,also TS11 und DS73 geprüft,das brücken von TS11 brachte nix.Habe dann direkt auf Pin7 vom Tuner 12 V gelegt und die Kanalsuche lief und es kam auch ein Bild.
Doch nun fährt die Box nur noch bis Booting hoch und schaltet sich dann ab.
Am Netzteil sind alle Spannungen da,ausser die 12V und am Tuner fehlen die 12V auch und die 5V an Pin9.
Hoffe mir kann jemand helfen.

[SoLaLa]

naja, da fehlen halt die 12V_OPB
die werden durch den TS11 geschaltet, also den erstmal nachmessen/austauschen

[Yellowfan]

Werde ich als erstes mal austauschen.War doch richtig,dass ich da auch einen BC638 oder BC640 benutzen kann?Finde den BC369 nämlich nicht bei Conrad oder Reichelt.

[SoLaLa]

Reichelt: BC 369; 0,06 EUR

[Yellowfan]

Danke habe ich jetzt auch gefunden.
Habe jetzt den TS11 (der völlig zerfetzt war ) und die DS73 getauscht.Ich erhalte nun auch die Spannungen an Pin3,Pin7 und Pin9,nur schaltet die Box immer noch ab bei Booting...
Habe dann alle Spannunngen im Netzteil geprüft und die sind alle da,nur die 12V an Pin18 vom Tuner sind nicht da,da liegen nur so 3V an.Woher bezieht der Tuner die 12V an Pin18?

[Rudi Ratlos 4711]

ucodes sind hochgeladen ?

RR4711

[Yellowfan]

Ja die Ucodes sind oben und ich habe mich vertan Pin 18 hat doch 12 V,hatte nicht beachtet das 17 nicht drauf ist.

[SoLaLa]

wo isn das Bootlog?

[Yellowfan]

So nun hier das Bootlog.


Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 634661 Bytes = 619 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-ce.53.1f.07.00.00-b2
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Aug 5 2002 - 09:06:03)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 634725 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 634661 Bytes = 619 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Die Dez 31 18:36:38 CET 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30816k available (1120k kernel code, 372k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:19:7e:d8
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.20/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.20/misc/event.o
event: init ...
Using /lib/modules/2.4.20/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20/misc/dvb_demux.o
Using /lib/modules/2.4.20/misc/dvbdev.o
Using /lib/modules/2.4.20/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
Using /lib/modules/2.4.20/misc/lcd.o
avia_core.c: load_dram_image: Microcode verify: 460 errors.
avia_core.c: load_dram_image: Microcode verify: 12180 errors.
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
insmod: init_module: avia: Input/output error
Using /lib/modules/2.4.20/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.20/misc/dmxdev.o
Using /lib/modules/2.4.20/misc/dvb_frontend.o
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Using /lib/modules/2.4.20/misc/avia_gt.o
insmod: unresolved symbol avia_set_pcr
Using /lib/modules/2.4.20/misc/dvb.o
insmod: unresolved symbol avia_wait
insmod: unresolved symbol avia_wr
insmod: unresolved symbol avia_command
insmod: unresolved symbol avia_rd
insmod: unresolved symbol avia_flush_pcr
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
Init VES1820
Using /lib/modules/2.4.20/misc/ves1820.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.20/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_dmx_release_section_filter
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_fake_queue_irq
insmod: unresolved symbol avia_gt_dmx_get_queue_irq
insmod: unresolved symbol avia_gt_dmx_set_filter_parameter_table
insmod: unresolved symbol register_demux
insmod: unresolved symbol avia_gt_dmx_set_pid_table
insmod: unresolved symbol avia_gt_dmx_force_discontinuity
insmod: unresolved symbol avia_gt_dmx_set_pid_control_table
insmod: unresolved symbol avia_gt_dmx_get_hw_sec_filt_avail
insmod: unresolved symbol avia_gt_dmx_get_queue_info
insmod: unresolved symbol avia_gt_dmx_set_section_filter
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_queue_irq_disable
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_message
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_free_irq
Using /lib/modules/2.4.20/misc/avia_gt_vbi.o
insmod: unresolved symbol avia_gt_get_info
Using /lib/modules/2.4.20/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.20/misc/avia_gt_oss.o
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_standby
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.20/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.1 2002/12/19 16:10:45 alexW Exp $

$Id: sectionsd.cpp,v 1.148 2002/12/09 20:07:52 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
$Id: zapit.cpp,v 1.286 2003/01/03 12:41:31 alexw Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conffor reading.

/var/tuxbox/config/zapit/services.xml: No such file or directory
[frontend.cpp:CFrontend:62] /dev/dvb/card0/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
Controld $Id: controld.cpp,v 1.88 2003/01/07 19:08:27 Zwen Exp $

[ConfigFile] Unable to open file /var/tuxbox/config/controld.conffor reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.389 2003/01/12 16:41:17 Zwen Exp $

[lcdd] time-skin not found -> using default...
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
CXA2092 found
Unmounting 'ramfs' on '/tmp'
umount: /tmp: Device or resource busy
Unmounting 'jffs2' on '/var'
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
Ready to shutdown system...

Sending SIGTERM to all processes[nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
System halt



Also wenn ich das richtig sehe,dann stimmt was mit dem Framebuffer nicht.

[SoLaLa]

avia_core.c: load_dram_image: Microcode verify: 460 errors.
avia_core.c: load_dram_image: Microcode verify: 12180 errors.

das is nich gut... garnicht gut

[Yellowfan]

Ja sieht ja auch nicht gut aus,aber woran liegt es?
Muss ich etwa die Box einschicken und machen lassen oder ist da selber was zu machen?

[SoLaLa]

also der microcode für den avia wird geladen und danach verifiziert, n paar Fehler können dabei durchaus auftreten ohne daß das nen nennenswerten Einfluß auf die Funktion hätte, aber wenns zuviele Fehler sind, dann geht nix mehr...
Avia oder dessen RAM austauschen würd ich mal sagen