Hallo,
habe eine defekte Nokia Kabel Box die keine Sender Empfängt.
Alle Tunerspannungen kommen am Tuner an.
Am BFG liegt keine Spannung an. TS11 auch ok.
Neben dem 10 Ohm Widerstand ist ein Grünes Bauteil, welches keinen Durchgang hat.
Habe die Vermutung, dass dieser defekt ist.
Kann mir einer sagen, was das für ein Bauteil das ist???
Tuner defekt!!!
-
geronimo25
- Interessierter
- Beiträge: 28
- Registriert: Sonntag 1. Dezember 2002, 19:13
-
SoLaLa
- Tuxboxer
- Beiträge: 6119
- Registriert: Mittwoch 3. April 2002, 00:32
-
geronimo25
- Interessierter
- Beiträge: 28
- Registriert: Sonntag 1. Dezember 2002, 19:13
-
geronimo25
- Interessierter
- Beiträge: 28
- Registriert: Sonntag 1. Dezember 2002, 19:13
So, hab mir die Drosselspule besorgt und auch gleich eingebaut.
Bos zusammengeschraubt, angeschlossen.... und.....kein Bild.
Analoges Bild verrauscht, als ob der BFG wieder defekt wäre.
Spannung an diesem: 12,38 V
Und hier dann gleich noch ein Bootlog.
Vielleicht kann man da noch mehr erkennen.
*debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-d3.09.80.07.00.00-f0
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/nokia-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/nokia-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/mpc8xx-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/mpc8xx-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/kernel/os in Flash-FS
debug: Got Block #0196
will verify ELF image, start= 0x800000, size= 202876
verify sig: 262
Branching to 0x40000
ppcboot 0.6.4 (Mar 2 2002 - 20:44:32)
Initializing...
CPU: PPC823ZTnnB2 at 67 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-43-b2-18
FLASH: 8 MB
LCD driver (KS0713) initialized
LCD logo at: 0x8F049 (0x1E00 bytes)
FB logo at: 0x90E71 (0x31C1 bytes)
AVIA Frambuffer
Input: serial
Output: serial
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
Kernel image at: 0x10020034 (0x8EFED bytes)
## Booting Linux kernel at 10020034 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 585645 Bytes = 571 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-pre8-dbox2 (von alexW) (gcc version 3.0.4) #16 Son Mai 19 1
9:32:22 UTC 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: ro root=1f03 console=ttyS0
WARNING: Frequency is not in HZ. Please consider using a newer bootloader!
WARNING: OLD intfreq = 67 busfreq = 67
WARNING: NEW intfreq = 67000000 busfreq = 67000000
Decrementer Frequency = 251250000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.56 BogoMIPS
Memory: 30920k available (1032k kernel code, 352k data, 64k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12 (20020219) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:43:b2:18
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x000c0000 : "idxfs (kernel, logos)"
0x000c0000-0x00160000 : "var (jffs2)"
0x00160000-0x00760000 : "root (cramfs)"
0x00760000-0x00800000 : "flfs (ppcboot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k init
init started: BusyBox v0.61.pre (2002.04.02-22:55+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
write 1 event's ...
write 1 event's ...
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
avia_gt_core: $Id: avia_gt_core.c,v 1.19 2002/05/09 19:54:19 obi Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.13 2002/05/09 22:25:23 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.86 2002/05/09 07:29:21 waldi Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_gv: $Id: avia_gt_gv.c,v 1.17 2002/05/09 22:23:30 obi Exp $
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.12 2002/05/08 12:56:41 obi Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.18 2002/05/01 21:51:35 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.18 2002/05/07 16:59:19 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.15 2002/05/13 22:38:36 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Init VES1820
i2c-core.o: driver VES1820 DVB demodulator registered.
attach_adapter
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
avia_gt_napi: $Id: avia_gt_napi.c,v 1.88 2002/05/07 16:59:19 Jolt Exp $
avia_gt_napi: warning, misaligned queue 0 (is 32a00, size 10000), aligning...
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.10 2002/05/06 02:18:18 obi Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.30 2002/05/03 16:47:35 obi Exp $
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 90x36
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
CXA2092 found
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
CXA2092 found
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
Network LCD-Driver $Id: lcdd.cpp,v 1.48 2002/05/15 23:32:12 McClean Exp $
[lcdd] load config
/var/tuxbox/config/lcdd.conf: No such file or directory
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
[FONT] FTC_Face_Requester (Micron/Regular)
$Id: sectionsd.cpp,v 1.126 2002/05/15 10:00:55 dirch Exp $
caching 504 hours
events are old 60min after their end time
dmxdev: set buffer size 40000 -> 60000
$Id: zapit.cpp,v 1.171 2002/05/04 15:25:25 McClean Exp $
/var/tuxbox/config/zapit/zapit.conf: No such file or directory
dvb.c: no frontend available
/dev/ost/frontend0: No such device or address
[zapit] unable to open frontend devices. bye.
Segmentation fault
Controld $Id: controld.cpp,v 1.58 2002/05/08 16:21:43 McClean Exp $
[controld] error while loading settings: /var/tuxbox/config/controld.conf
[controld] using defaults
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
dmxdev: set buffer size 40000 -> 60000
[nhttpd] Neutrino HTTP-Server starting..
/var/tuxbox/config/nhttpd.conf: No such file or directory
zapitclient: connect: No such file or directory
zapitclient: connect: No such file or directory
dmxdev: set buffer size 40000 -> 60000
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.275 2002/05/17 13:06:5[AVS] i2c erro
r -121
0 woglinde Exp $
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
fbcon_setup: No support for fontwidth 8
fbcon_setup: type 0 (aux 0, depth
not supported
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
/var/tuxbox/config/scan.conf: No such file or directory
[neutrino] error while loading scan-settings, using defaults!
Stimmt da vielleicht auch etwas mit dem I2C Bus nicht???
Bos zusammengeschraubt, angeschlossen.... und.....kein Bild.
Analoges Bild verrauscht, als ob der BFG wieder defekt wäre.
Spannung an diesem: 12,38 V
Und hier dann gleich noch ein Bootlog.
Vielleicht kann man da noch mehr erkennen.
*debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-d3.09.80.07.00.00-f0
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/nokia-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/nokia-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
File /root/platform/mpc8xx-dbox2/kernel/os not found: No such file or directory
boot flash /root/platform/mpc8xx-dbox2/kernel/os failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/kernel/os in Flash-FS
debug: Got Block #0196
will verify ELF image, start= 0x800000, size= 202876
verify sig: 262
Branching to 0x40000
ppcboot 0.6.4 (Mar 2 2002 - 20:44:32)
Initializing...
CPU: PPC823ZTnnB2 at 67 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-43-b2-18
FLASH: 8 MB
LCD driver (KS0713) initialized
LCD logo at: 0x8F049 (0x1E00 bytes)
FB logo at: 0x90E71 (0x31C1 bytes)
AVIA Frambuffer
Input: serial
Output: serial
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
Kernel image at: 0x10020034 (0x8EFED bytes)
## Booting Linux kernel at 10020034 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 585645 Bytes = 571 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-pre8-dbox2 (von alexW) (gcc version 3.0.4) #16 Son Mai 19 1
9:32:22 UTC 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: ro root=1f03 console=ttyS0
WARNING: Frequency is not in HZ. Please consider using a newer bootloader!
WARNING: OLD intfreq = 67 busfreq = 67
WARNING: NEW intfreq = 67000000 busfreq = 67000000
Decrementer Frequency = 251250000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.56 BogoMIPS
Memory: 30920k available (1032k kernel code, 352k data, 64k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12 (20020219) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:43:b2:18
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x000c0000 : "idxfs (kernel, logos)"
0x000c0000-0x00160000 : "var (jffs2)"
0x00160000-0x00760000 : "root (cramfs)"
0x00760000-0x00800000 : "flfs (ppcboot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k init
init started: BusyBox v0.61.pre (2002.04.02-22:55+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
write 1 event's ...
write 1 event's ...
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
avia_gt_core: $Id: avia_gt_core.c,v 1.19 2002/05/09 19:54:19 obi Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.13 2002/05/09 22:25:23 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.86 2002/05/09 07:29:21 waldi Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_gv: $Id: avia_gt_gv.c,v 1.17 2002/05/09 22:23:30 obi Exp $
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.12 2002/05/08 12:56:41 obi Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.18 2002/05/01 21:51:35 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.18 2002/05/07 16:59:19 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.15 2002/05/13 22:38:36 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Init VES1820
i2c-core.o: driver VES1820 DVB demodulator registered.
attach_adapter
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
i2c-CAM read error.
avia_gt_napi: $Id: avia_gt_napi.c,v 1.88 2002/05/07 16:59:19 Jolt Exp $
avia_gt_napi: warning, misaligned queue 0 (is 32a00, size 10000), aligning...
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.10 2002/05/06 02:18:18 obi Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.30 2002/05/03 16:47:35 obi Exp $
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 90x36
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
CXA2092 found
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
CXA2092 found
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
Network LCD-Driver $Id: lcdd.cpp,v 1.48 2002/05/15 23:32:12 McClean Exp $
[lcdd] load config
/var/tuxbox/config/lcdd.conf: No such file or directory
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[AVS] i2c error -121
i2c-CAM read error.
[AVS] i2c error -121
[FONT] FTC_Face_Requester (Micron/Regular)
$Id: sectionsd.cpp,v 1.126 2002/05/15 10:00:55 dirch Exp $
caching 504 hours
events are old 60min after their end time
dmxdev: set buffer size 40000 -> 60000
$Id: zapit.cpp,v 1.171 2002/05/04 15:25:25 McClean Exp $
/var/tuxbox/config/zapit/zapit.conf: No such file or directory
dvb.c: no frontend available
/dev/ost/frontend0: No such device or address
[zapit] unable to open frontend devices. bye.
Segmentation fault
Controld $Id: controld.cpp,v 1.58 2002/05/08 16:21:43 McClean Exp $
[controld] error while loading settings: /var/tuxbox/config/controld.conf
[controld] using defaults
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
dmxdev: set buffer size 40000 -> 60000
[nhttpd] Neutrino HTTP-Server starting..
/var/tuxbox/config/nhttpd.conf: No such file or directory
zapitclient: connect: No such file or directory
zapitclient: connect: No such file or directory
dmxdev: set buffer size 40000 -> 60000
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.275 2002/05/17 13:06:5[AVS] i2c erro
r -121
0 woglinde Exp $
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
fbcon_setup: No support for fontwidth 8
fbcon_setup: type 0 (aux 0, depth
not supportedavia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
/var/tuxbox/config/scan.conf: No such file or directory
[neutrino] error while loading scan-settings, using defaults!
Stimmt da vielleicht auch etwas mit dem I2C Bus nicht???
-
geronimo25
- Interessierter
- Beiträge: 28
- Registriert: Sonntag 1. Dezember 2002, 19:13
Habe dann jetzt noch einmal den BFG getauscht.
Box angeschlossen....klares analoges Bild auf dem Fernseher, aber jetzt startet die Box nicht mehr (nur noch grün hinterleuchtetes Display). Und der BGA Chip wird ratz fatz heiss (ca. 3 sek. nach stecken des Netzsteckers wird der richtig heiss!
Wenn noch einer einen Tip hat....
Box angeschlossen....klares analoges Bild auf dem Fernseher, aber jetzt startet die Box nicht mehr (nur noch grün hinterleuchtetes Display). Und der BGA Chip wird ratz fatz heiss (ca. 3 sek. nach stecken des Netzsteckers wird der richtig heiss!
Wenn noch einer einen Tip hat....
-
SoLaLa
- Tuxboxer
- Beiträge: 6119
- Registriert: Mittwoch 3. April 2002, 00:32
-
geronimo25
- Interessierter
- Beiträge: 28
- Registriert: Sonntag 1. Dezember 2002, 19:13
Ja, genau der.
So ein m...!!!
Hab nix anderes gemacht, als den BFG nochmals getauscht. Und nochmal alles kontrolliert. Hab durch den tausch auch keinen kurzschluss dadurch verursacht.
Konnte die Box auch einwandfrei nach BFG tausch flashen.
Als ich dann die Box ans Kabelnetz angeschlossen hab, hatte ich zwar ein glasklares durchgeschleiftes analoges Fernsehbild, doch im Display der Box war alles nur noch grünlich hinterleuchtet.
Und jetzt weiss ich nicht mehr, wo ich da jetzt ansetzen soll.
Wäre zu schade, die Box jetzt wegzuwerfen.
Kann damit einer etwas anfangen (Ansatzpunkt?) ???
So ein m...!!!
Hab nix anderes gemacht, als den BFG nochmals getauscht. Und nochmal alles kontrolliert. Hab durch den tausch auch keinen kurzschluss dadurch verursacht.
Konnte die Box auch einwandfrei nach BFG tausch flashen.
Als ich dann die Box ans Kabelnetz angeschlossen hab, hatte ich zwar ein glasklares durchgeschleiftes analoges Fernsehbild, doch im Display der Box war alles nur noch grünlich hinterleuchtet.
Und jetzt weiss ich nicht mehr, wo ich da jetzt ansetzen soll.
Wäre zu schade, die Box jetzt wegzuwerfen.
Kann damit einer etwas anfangen (Ansatzpunkt?) ???
-
SoLaLa
- Tuxboxer
- Beiträge: 6119
- Registriert: Mittwoch 3. April 2002, 00:32
puuuuuuuh,
Ansantzpunkt hab ich da keinen... und wenn der Prozi heiß wird, dann ist der im allgemeinen auch schon kaputt... weiß der Geier warum...
ich könnt mir höchstens vorstellen, daß der schon vorher nen partiellen Schaden hatte (so nach dem prinzip: Belastung auf dem 12Vzweig zu hoch und deshalb regelt das Netzteil nach, wodurch der Prozi dann vielleicht mal 4 Volt hatte... keine Ahnung
)
Ansantzpunkt hab ich da keinen... und wenn der Prozi heiß wird, dann ist der im allgemeinen auch schon kaputt... weiß der Geier warum...
ich könnt mir höchstens vorstellen, daß der schon vorher nen partiellen Schaden hatte (so nach dem prinzip: Belastung auf dem 12Vzweig zu hoch und deshalb regelt das Netzteil nach, wodurch der Prozi dann vielleicht mal 4 Volt hatte... keine Ahnung
)never change a running system