Beim booten fehlt auch der Debug-Screen
Inzwischen hab ich noch festgestellt, dass es vermutlich ein thermisches Problem sein könnte... Ich hab die Box in einem Schrank stehen. Wenn die Tür auf ist und die Box ne Weile im DeepStandby war, ist das Problem verschwunden. Mache ich die Tür zu, kommt es wieder. Auf den größeren Chips (Prozessor, AVIA etc.) hatte ich eh vorsorglich Kühlkörper verbaut. Welches IC ist denn für das Display zuständig? Sollte ich dort auch einen Kühlkörper nutzen?
Hier mal nen aktueller Log:
Code: Alles auswählen
Âdebug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: LCD init error -1
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-dc.76.05.08.00.00-d1
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0008
debug: Got Block #0012
debug: Got Block #0016
debug: Got Block #0020
debug: Got Block #0024
debug: Got Block #0028
debug: Got Block #0032
debug: Got Block #0036
debug: Got Block #0040
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 172152
verify sig: 262
Branching to 0x40000
U-Boot 1.3.3 (Tuxbox) (Jun 11 2008 - 22:26:40)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . | / - . \ | done.
env: found "console"
env: found "baudrate"
env: found "dbox_duplex"
env: found "lcd_inverse"
env: found "lcd_contrast"
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 689377 bytes loaded to 0x100000
## Booting kernel from Legacy Image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 689313 Bytes = 673.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.36.6-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #1 Mi 11. Jun 22:31:34 CEST 2008
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex=0
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30788k available (1172k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:33:08:65
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (SquashFS_LZMA)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.11.1 (2008-07-13 22:24:40 CEST)
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: IDE-Interface detected, Vendor: Gurgel
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
dboxide: $Id: main.c,v 1.12 2008/07/22 19:25:14 dbt Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of IDE-Interface is at: 0xc394f000
dboxide: IDE-Interface detected, Vendor: Gurgel
dboxide: sreset succeeded
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Probing IDE interface ide0...
hda: SAMSUNG HM160JI, ATA DISK drive
hdb: no response (status = 0xa1), resetting drive
hdb: no response (status = 0xa1)
ide0 at 0x010-0x017,0x04e on irq 12
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 312581808 sectors (160042 MB) w/8192KiB Cache, CHS=19457/255/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
SGI XFS with no debug enabled
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Adding Swap: 136544k swap-space (priority -1)
XFS mounting filesystem ide0(3,2)
XFS mounting filesystem ide0(3,3)
/dev/ide/host0/bus0/target0/lun0/disc:
setting 32-bit IO_support flag to 1
setting drive write-caching to 0 (off)
setting standby to 60 (5 minutes)
IO_support = 1 (32-bit)
write-caching = 0 (off)
jtginfo $Id: jtginfo.c,v 2.0 2008/04/16 22:16:44 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
ves1x93: Detected ves1993
DVB: registering frontend 0:0 (VES1993)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Thu Jan 1 12:00:00 CET 1970
$Id: sectionsd.cpp,v 1.265 2008/08/16 19:23:18 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 7 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/mybouquets.xml: No such file or directory
$Id: zapit.cpp,v 1.410 2008/04/25 21:23:23 houdini Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0
[getservices] dup transponder id 9 onid 85
[getservices] dup transponder id 444 onid 1
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 421 onid 1
[getservices] dup transponder id 3F8 onid 1
[getservices] dup transponder id 402 onid 1
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 42C onid 1
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 4 onid 85
[getservices] dup transponder id 43A onid 1
[getservices] dup transponder id 1 onid 85
[getservices] dup transponder id 7 onid 85
[getservices]: removing 'SAT.1-CH' (service_id=0x30): FAILED!
[getservices] dup transponder id 443 onid 1
[getservices] dup transponder id 444 onid 1
[getservices] dup transponder id 446 onid 1
[getservices] dup transponder id 5 onid 85
[getservices] dup transponder id 21 onid 85
[getservices] dup transponder id 454 onid 1
[getservices] dup transponder id 459 onid 1
[getservices] dup transponder id 45B onid 1
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.130 2008/01/03 11:09:27 seife Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[controld]: ROUTEVIDEO v1 = 1 a1 = 0 v2 = 0 a2 = 0 fblk=0
[controld] format: 4:3(LB)
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...rdate: timeout connecting to time server
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
neutrino: /lib/libpng12.so.0: no version information available (required by neutrino)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
imageinfo: JTG-Image [IDE] (2.3.0)
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[neutrino] initialized everything
PES, queue 0 normal.
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
[timeThread] - 21.08.2008 22:42:50, tim: Thu Aug 21 22:42:50 2008
12:00:33.797 [sectionsd] DMX::readNbytes received POLLERR, pid 0x12, filter[0] filter 0x4e mask
0xff
12:00:33.802 dmxSDT: going to sleep...
[timeThread] Time set via DVB, going to sleep for 21600 seconds.
[lcdd] set invert failed!: Device or resource busy
22:42:50.172 dmxCN: going to sleep...
22:42:50.342 eit_set_update_filter, servicekey = 0x4530001445d, current version 28
22:42:59.978 dmxSDT: going to sleep...
Außer den Display-Problemen ist mir aber noch kein Fehler aufgefallen...
